GarrettCom manual Eight-Port Copper Module, 6K8-RJ45, Speed when on and at 10 MB

Page 17

Magnum 6K8-Series Industrial Field Switch

Installation and User Guide (04/07)

powered-up device at the other end of the cable) in order for a LK LED to provide valid indications of operating conditions on that port.

2.2.3Eight-Port Copper Module, 6K8-RJ45

The 6K8-Series’s 8-port Copper port module, model 6K8-RJ45, provides eight 10/100Mb switched RJ-45 ports. The 10/100Mb switched ports normally (as a default setting) are independently N-way auto-negotiating, and auto-crossover (MDIX) for operation at 10 or 100Mb speed in full- or half-duplex mode, i.e., each independently selects a mode and speed to match the device at the other end of the twisted pair cable.

(See Section 4.3 for auto-negotiation and MDIX details). The auto-crossover feature will automatically determine the other side of connection to make the connection, and eliminate the need of crossover cable.

On the model 6K8-RJ45 module, there are four LEDs for each port, two in the connector and two separate. The LK (Link) LED indicates, “ready for operation” on that port when lit. The blinking ACT (Activity) LED indicates receiving Activity on that port

when lit. The 10/100 LED

1

3

5

7

indicates operation at 100Mb

10/100

LK

speed when ON and at 10 MB

ACT

F/ H

speed when OFF (when auto-

2

4

6

8

10/100

LK

negotiation is not disabled).

The FDX/HDX LED is ON to

F/H

ACT

indicate full-duplex operation

and OFF to indicate half-duplex mode. A twisted pair cable must be connected into an RJ-45 port and the Link (LK) indicator for that port must be ON (indicating there is a powered-up device at the other end of the cable) in order for a LK LED to provide valid indications of operating conditions on that port.

Using the 6K8-Series (MNS-6K) management software, the user may disable auto-negotiation and fix the desired operation of each RJ-45 port. User may select 10Mb or 100Mb speed and full- or half-duplex mode per-port as per user requirement. (See Magnum MNS-6K Software Manual for details info.).

www . GarrettCom . com

12

Image 17

Contents Industrial Field Switch Trademarks Canadian Emission Contacting GarrettCom, IncIntroduction Table of ContentsInstallation 14 6KM-BLNK TroubleshootingOverview Magnum LinePerformance Technical SpecificationsNetwork Standards and Compliance, hardware Maximum 10 Mbps Ethernet Segment LengthsFiber Single-mode connector types Fiber Multi-mode connector types supportedAlarm Relay Contacts Management Console connectorPer-port MDI or Mdix on RJ-45 DC Power Supply OptionsMountings Agency Approvals Magnum 6K8Magnum 6K8 Port Modules Configuration OptionsOrdering Information GBIC1000Mb Transceiver options for Mangum 6K8-Series Introduction Inspecting the Package and Product Product Description Magnum 6K8-Series 6K8 1a Magnum 6K8-Series, Industrial Field Switch Www . GarrettCom . com Operate in full-duplex mode for best Normally are set factory default toFiber distance and performance. Using Eight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb FiberSpeed when on and at 10 MB When lit. The 10/100 LED Indicates operation at 100MbSpeed when OFF when auto Negotiation is not disabled FDX/HDX LED is on toST or SC @RJ-45 + 2@ 100MbFour-Port 10 MB and 100Mb mm Fiber ST Modules Gigabit 1000Mbps port modules 7a GBPM-2OTX Two Gigabit port option Packet Prioritization, 802.1p QOS Gbic DescriptionManaged Network Software MNS-6K for Magnum 6K8-Series Frame Buffering and Flow ControlWww . GarrettCom . com „ Large selection of built-in fiber options at 10/100/1000Mb Applications Interne Control Center Scada Mounting Instructions Connecting Ethernet Media Locating Magnum 6K8-Series SwitchesIeee Standard Media Type Max. Distance Port Module Fiber CopperConnecting Single-Mode Fiber Optic Connecting Fiber Optic ST-type, twist-lockConnecting Fiber Optic SC-type, Snap-In 100BASE-TX Media Ieee StandardWww . GarrettCom . com DIN-Rail Mounting Quantity Description Din-Rail kit Installation proceduresWww . GarrettCom . com Mounting Dimensions for 6K8 with metal brackets Powering the Magnum 6K8-Series Industrial Field Switch Www . GarrettCom . com Preparation for Installing and Removing 6KPMVs from 6K8’s 6K8-Series Port Module 6KPMV Installation1a Removing the Top panel from the Chassis base of the unit Remove Chassis Cover2b Granddaughter Board shown separately Installing 6KPM Cards in the Magnum 6K8-Series2a a Magnum 6K8 unit with main board motherboard only Female latch connector 2h sliding in the top cover onto the chassis base track Removing a 6KPM Card Removing 6KPM CardsRetaining screws shown by arrows Remove 6KPM Card Enlarged view of Magnum 6K8-Series Console Port area Connecting a Management Console Terminal to Magnum 6K81 RS-232 DB-9 Console Com port Serial port pin assignments Switching FunctionalityDB-9 Console port connector Address Learning Dual LEDs Status on TOP and Front of the 6K8-Series unitFiltering and Forwarding Auto-Cross Mdix and Auto-negotiation, for RJ-45 ports Flow-control, Ieee 802.3x Standard Www . GarrettCom . com ’cvr 6KP4V6KPMV Module Description Introduction Magnum 6K8 Industrial Field Switch Port ModulesSwitch, the copper port Segments. When installed in aDual speed copper ports Magnum 6K8-Series Managed1b 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module Magnum 6KP6 Mode 100Mbps fiber opticTransceivers all in one module. This Activity ACT, Link LK,10/100Mbps RJ-45 Ports 2@100Mbps single Mode FX-SC-type, snap Connector6KP6-RJSSC 4@ Port@ 100Mbps Multi-Mode Fiber port 5 6KP8-MTRJ, 8 @100Mb multi-mode FX, Mtrj Small-Form-factorMagnum 6KP8-45MT Module is a combo module with Port multi-mode fiber LC connector 10/100Mb 8-Port 9 6KP8-RJ45 Twisted PairPoE LEDs Summary 45-2MT eight ports Module is a 12a GBIC-LXSC Gigabit fiber 1000Mb, multi-mode SC Connector GBIC-SXSC Gigabit fiber 1000Mb, multi-mode SC ConnectorStandard 1@ 1000Mb Fiber SC + 2@ 100Mb SCGBPM-2OTX Two Gigabit option Before Calling for Assistance When Calling for Assistance No Problem Found Appendix B Internal DC Power Supply Options B3.0 Applications for DC Powered Ethernet Switches B2.0 -48VDC, 24VDC and 125VDC POWER, Theory of OperationB4.0 6K8-SERIES, -48V, 24, 125 or 5VDC Installation B7.0 Troubleshooting C4.0 Features and Benefits of the DUAL-SOURCE Design C5.1 UL Requirements External Terminal Block on a Magnum 6K8 -48VDCExample Magnum 6K8 -24VDC C6.0 Ordering Information Optional

Related manuals

Manual 69 pages 29.41 Kb