GarrettCom 6K8 manual Gbic Description, Packet Prioritization, 802.1p QOS

Page 22

Magnum 6K8-Series Industrial Field Switch

Installation and User Guide (04/07)

Model #

GBIC-SXSC

GBIC-LXSC10

GBIC-LXSC25

GBIC-TP

GBIC-ZXSC40

GBIC-ZXSC70

GBIC Description

One 1000BASE-SX port with multi-mode SC fiber connector

One 1000BASE-LX/LH port 1310nm single- mode SC 10Km

One 1000BASE-LX/LH port 1310nm single- mode SC 25Km

One IEEE 802.3ab TP port, RJ-45 connector

One 1000BASE-ZX port 1550nm single- mode SC 40Km

One 1000BASE-ZX port 1550nm single- mode SC 70Km

The Gigabit ports are set by factory as AUTO by default but can be configured as per the convenience using the MNS-6K management firmware.

2.2.8Packet Prioritization, 802.1p QOS

Quality of Service means providing consistent predictable data delivery to

users from datagram paths that go all across a network. As a LAN device, the Magnum 6K8-Series can do its part to prevent any QOS degradation while it is handling Ethernet traffic through its ports and buffers.

The Magnum 6K8-Series switching hardware supports the IEEE 802.1p standard and fulfills its role in support of QOS, giving packet processing priority-to- priority tagged packets according to the 802.1p standard. In addition to hardware support for QOS, the MNS software (Rel3) supports two priority queues that can be shared across the eight levels of defined packet priorities for application-specific priority control by the user through software configuration settings.

www . GarrettCom . com

17

Image 22

Contents Industrial Field Switch Trademarks Contacting GarrettCom, Inc Canadian EmissionInstallation Table of ContentsIntroduction Troubleshooting 14 6KM-BLNKMagnum Line OverviewNetwork Standards and Compliance, hardware Technical SpecificationsPerformance Maximum 10 Mbps Ethernet Segment LengthsAlarm Relay Contacts Fiber Multi-mode connector types supportedFiber Single-mode connector types Management Console connectorMountings DC Power Supply OptionsPer-port MDI or Mdix on RJ-45 Agency Approvals Magnum 6K8Ordering Information Configuration OptionsMagnum 6K8 Port Modules GBIC1000Mb Transceiver options for Mangum 6K8-Series Introduction Inspecting the Package and Product Product Description Magnum 6K8-Series 6K8 1a Magnum 6K8-Series, Industrial Field Switch Www . GarrettCom . com Fiber distance and performance. Using Normally are set factory default toOperate in full-duplex mode for best Eight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb FiberSpeed when OFF when auto When lit. The 10/100 LED Indicates operation at 100MbSpeed when on and at 10 MB Negotiation is not disabled FDX/HDX LED is on to@RJ-45 + 2@ 100Mb ST or SCFour-Port 10 MB and 100Mb mm Fiber ST Modules Gigabit 1000Mbps port modules 7a GBPM-2OTX Two Gigabit port option Gbic Description Packet Prioritization, 802.1p QOSFrame Buffering and Flow Control Managed Network Software MNS-6K for Magnum 6K8-SeriesWww . GarrettCom . com „ Large selection of built-in fiber options at 10/100/1000Mb Applications Interne Control Center Scada Mounting Instructions Ieee Standard Media Type Max. Distance Port Module Fiber Locating Magnum 6K8-Series SwitchesConnecting Ethernet Media CopperConnecting Fiber Optic SC-type, Snap-In Connecting Fiber Optic ST-type, twist-lockConnecting Single-Mode Fiber Optic Media Ieee Standard 100BASE-TXWww . GarrettCom . com DIN-Rail Mounting Din-Rail kit Installation procedures Quantity DescriptionWww . GarrettCom . com Mounting Dimensions for 6K8 with metal brackets Powering the Magnum 6K8-Series Industrial Field Switch Www . GarrettCom . com 6K8-Series Port Module 6KPMV Installation Preparation for Installing and Removing 6KPMVs from 6K8’sRemove Chassis Cover 1a Removing the Top panel from the Chassis base of the unit2a a Magnum 6K8 unit with main board motherboard only Installing 6KPM Cards in the Magnum 6K8-Series2b Granddaughter Board shown separately Female latch connector 2h sliding in the top cover onto the chassis base track Retaining screws shown by arrows Remove 6KPM Card Removing 6KPM CardsRemoving a 6KPM Card Connecting a Management Console Terminal to Magnum 6K8 Enlarged view of Magnum 6K8-Series Console Port areaDB-9 Console port connector Switching Functionality1 RS-232 DB-9 Console Com port Serial port pin assignments Filtering and Forwarding Dual LEDs Status on TOP and Front of the 6K8-Series unitAddress Learning Auto-Cross Mdix and Auto-negotiation, for RJ-45 ports Flow-control, Ieee 802.3x Standard Www . GarrettCom . com 6KP4V ’cvrIntroduction Magnum 6K8 Industrial Field Switch Port Modules 6KPMV Module DescriptionDual speed copper ports Segments. When installed in aSwitch, the copper port Magnum 6K8-Series Managed1b 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module Transceivers all in one module. This Mode 100Mbps fiber opticMagnum 6KP6 Activity ACT, Link LK,6KP6-RJSSC 4@ 2@100Mbps single Mode FX-SC-type, snap Connector10/100Mbps RJ-45 Ports 5 6KP8-MTRJ, 8 @100Mb multi-mode FX, Mtrj Small-Form-factor Port@ 100Mbps Multi-Mode Fiber portMagnum 6KP8-45MT Module is a combo module with Port multi-mode fiber LC connector 9 6KP8-RJ45 Twisted Pair 10/100Mb 8-PortPoE LEDs Summary 45-2MT eight ports Module is a Standard 1@ 1000Mb Fiber SC + 2@ GBIC-SXSC Gigabit fiber 1000Mb, multi-mode SC Connector12a GBIC-LXSC Gigabit fiber 1000Mb, multi-mode SC Connector 100Mb SCGBPM-2OTX Two Gigabit option Before Calling for Assistance When Calling for Assistance No Problem Found Appendix B Internal DC Power Supply Options B2.0 -48VDC, 24VDC and 125VDC POWER, Theory of Operation B3.0 Applications for DC Powered Ethernet SwitchesB4.0 6K8-SERIES, -48V, 24, 125 or 5VDC Installation B7.0 Troubleshooting C4.0 Features and Benefits of the DUAL-SOURCE Design External Terminal Block on a Magnum 6K8 -48VDC C5.1 UL RequirementsC6.0 Ordering Information Optional Example Magnum 6K8 -24VDC

Related manuals

Manual 69 pages 29.41 Kb