GarrettCom 6K8 Connecting Fiber Optic ST-type, twist-lock, Connecting Single-Mode Fiber Optic

Page 32

Magnum 6K8-Series Industrial Field Switch

Installation and User Guide (04/07)

3.2.1Connecting Fiber Optic ST-type, “twist-lock”

The following procedure applies to installations using a PM with ST-type fiber connectors. This procedure applies to ports using a 6K8-Series module, MST- type port.

1.Before connecting the fiber optic cable, remove the protective dust caps from the tips of the connectors on the PM. Save these dust caps for future use.

2.Wipe clean the ends of the dual connectors with a soft cloth or lint-free lens tissue dampened in alcohol. Make certain the connectors are clean before connecting.

Note: One strand of the duplex fiber optic cable is coded using color bands at regular intervals; you must use the color-coded strand on the associated ports at each end of the fiber optic segment.

3.Connect the Transmit (TX) port (light colored post) on the Magnum PM to the Receive (RX) port of the remote device. Begin with the color-coded strand of the cable for this first TX-to-RX connection.

4.Connect the Receive (RX) port (dark colored post on the PM) to the Transmit

(TX) port of the remote device. Use the non-color coded fiber strand for this.

5.The LINK LED on the front of the PM will illuminate when a proper connection has been established at both ends (and when power is ON in the unit). If LINK is not lit after cable connection, the normal cause is improper cable polarity. Swap the fiber cables at the PM connector to remedy this situation.

3.2.2Connecting Fiber Optic SC-type, "Snap-In"

The following procedure applies to installations using a PM with SC-type fiber

connectors, i.e., using 6K-MSC, 6K-SSC single-mode.

While connecting fiber media to SC connectors, simply snap the two square male connectors into the SC female jacks of the 6KPM module until it clicks and secures.

3.2.3Connecting Single-Mode Fiber Optic

When using single-mode fiber cable, be sure to use single-mode fiber port

connectors. Single-mode fiber cable has a smaller diameter than multi-mode fiber cable (9/125 microns for single-mode, 50/125 or 62.5/125 microns for multi-mode where xx/xx

www . GarrettCom . com

27

Image 32
Contents Industrial Field Switch Trademarks Contacting GarrettCom, Inc Canadian EmissionIntroduction Table of ContentsInstallation Troubleshooting 14 6KM-BLNKMagnum Line OverviewTechnical Specifications PerformanceNetwork Standards and Compliance, hardware Maximum 10 Mbps Ethernet Segment LengthsFiber Multi-mode connector types supported Fiber Single-mode connector typesAlarm Relay Contacts Management Console connectorDC Power Supply Options Per-port MDI or Mdix on RJ-45Mountings Agency Approvals Magnum 6K8Magnum 6K8 Port Modules Configuration OptionsOrdering Information GBIC1000Mb Transceiver options for Mangum 6K8-Series Introduction Inspecting the Package and Product Product Description Magnum 6K8-Series 6K8 1a Magnum 6K8-Series, Industrial Field Switch Www . GarrettCom . com Normally are set factory default to Operate in full-duplex mode for bestFiber distance and performance. Using Eight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb FiberWhen lit. The 10/100 LED Indicates operation at 100Mb Speed when on and at 10 MBSpeed when OFF when auto Negotiation is not disabled FDX/HDX LED is on to@RJ-45 + 2@ 100Mb ST or SCFour-Port 10 MB and 100Mb mm Fiber ST Modules Gigabit 1000Mbps port modules 7a GBPM-2OTX Two Gigabit port option Gbic Description Packet Prioritization, 802.1p QOSFrame Buffering and Flow Control Managed Network Software MNS-6K for Magnum 6K8-SeriesWww . GarrettCom . com „ Large selection of built-in fiber options at 10/100/1000Mb Applications Interne Control Center Scada Mounting Instructions Locating Magnum 6K8-Series Switches Connecting Ethernet MediaIeee Standard Media Type Max. Distance Port Module Fiber CopperConnecting Single-Mode Fiber Optic Connecting Fiber Optic ST-type, twist-lockConnecting Fiber Optic SC-type, Snap-In Media Ieee Standard 100BASE-TXWww . GarrettCom . com DIN-Rail Mounting Din-Rail kit Installation procedures Quantity DescriptionWww . GarrettCom . com Mounting Dimensions for 6K8 with metal brackets Powering the Magnum 6K8-Series Industrial Field Switch Www . GarrettCom . com 6K8-Series Port Module 6KPMV Installation Preparation for Installing and Removing 6KPMVs from 6K8’sRemove Chassis Cover 1a Removing the Top panel from the Chassis base of the unit2b Granddaughter Board shown separately Installing 6KPM Cards in the Magnum 6K8-Series2a a Magnum 6K8 unit with main board motherboard only Female latch connector 2h sliding in the top cover onto the chassis base track Removing a 6KPM Card Removing 6KPM CardsRetaining screws shown by arrows Remove 6KPM Card Connecting a Management Console Terminal to Magnum 6K8 Enlarged view of Magnum 6K8-Series Console Port area1 RS-232 DB-9 Console Com port Serial port pin assignments Switching FunctionalityDB-9 Console port connector Address Learning Dual LEDs Status on TOP and Front of the 6K8-Series unitFiltering and Forwarding Auto-Cross Mdix and Auto-negotiation, for RJ-45 ports Flow-control, Ieee 802.3x Standard Www . GarrettCom . com 6KP4V ’cvrIntroduction Magnum 6K8 Industrial Field Switch Port Modules 6KPMV Module DescriptionSegments. When installed in a Switch, the copper portDual speed copper ports Magnum 6K8-Series Managed1b 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module Mode 100Mbps fiber optic Magnum 6KP6Transceivers all in one module. This Activity ACT, Link LK,10/100Mbps RJ-45 Ports 2@100Mbps single Mode FX-SC-type, snap Connector6KP6-RJSSC 4@ 5 6KP8-MTRJ, 8 @100Mb multi-mode FX, Mtrj Small-Form-factor Port@ 100Mbps Multi-Mode Fiber portMagnum 6KP8-45MT Module is a combo module with Port multi-mode fiber LC connector 9 6KP8-RJ45 Twisted Pair 10/100Mb 8-PortPoE LEDs Summary 45-2MT eight ports Module is a GBIC-SXSC Gigabit fiber 1000Mb, multi-mode SC Connector 12a GBIC-LXSC Gigabit fiber 1000Mb, multi-mode SC ConnectorStandard 1@ 1000Mb Fiber SC + 2@ 100Mb SCGBPM-2OTX Two Gigabit option Before Calling for Assistance When Calling for Assistance No Problem Found Appendix B Internal DC Power Supply Options B2.0 -48VDC, 24VDC and 125VDC POWER, Theory of Operation B3.0 Applications for DC Powered Ethernet SwitchesB4.0 6K8-SERIES, -48V, 24, 125 or 5VDC Installation B7.0 Troubleshooting C4.0 Features and Benefits of the DUAL-SOURCE Design External Terminal Block on a Magnum 6K8 -48VDC C5.1 UL RequirementsC6.0 Ordering Information Optional Example Magnum 6K8 -24VDC
Related manuals
Manual 69 pages 29.41 Kb