ICP DAS USA DN-3000 Transfer Options, Download Project to DN3000, Upload Project from DN3000

Page 47

Transferring Project Files

Communication

“Startup”

Screen

TRANSFER OPTIONS

Download Project to DN3000

Allows you to transfer (download) any created project file from the PC to the DN-3000.

Upload Project from DN3000

Allows you to transfer (upload) the project file stored in the DN-3000 to the PC. The computer will upload the project file under the name “NONAME.” You must save this uploaded project file using the “SAVE AS” command from the “PROJECT” window and enter your own file name.

Verify

This feature allows you to verify a project file within your computer against the current project file stored in the DN-3000 unit. After completing the verification process, if the project files are the same, a message will appear stating “Data Verified OK”. If the files are different, a message will be displayed stating which part of the project files are different.

Check Application in DN3000

This is allows you to check what type of project file is loaded (DeviceNet to PLC, DeviceNet to Motor Drives) and which protocols have been loaded for each of the communication ports.

41

Image 47

Contents DN-3000 Page Warranty Warranty & NoticesTable of Contents Application Notes Motor Drives Page Introduction IntroductionGeneral Information Software InstallationInstallation Software START-UP Software InformationCreating a Project File Creating Project FilesProject Types Additional Project Menu Sub-Headings Device Profile DeviceNet to PLCs or DevicesDevicenet to Plcs or Devices DeviceNet Host to Multi-Dropped Serial PLCs Example ApplicationsDeviceNet Host to Serial PLC with Pass-Through Connection Multiple DN-3000s with Different PLC or Device Types DeviceNet to PLCs or Devices Edit Menu Configuring Port #1, DevicenetMAC ID of DN3000 PLC/Device Protocol Configuring Port #2 Plcs or DevicesWire RS422 or RS485 Communications Intermessage Time-Out Configuring Port # 3 PassthroughUse I/O Data Data ConfigurationOutput Data Use Command BlockUse Diagnostics Output Data SizeInput Data Input Data SizeOutput Data Table Register Number Use Output WordPLC/Device Address File Number Allen-Bradley PLCs onlyInput Data Table PLC/DeviceAddress Use Input WordCommand Block Devicenet to Motor Drives DeviceNet to Motor DrivesDeviceNet Host to Multi-Dropped Serial Motor Drives DeviceNet Host to Serial Motor DriveMultiple DN-3000s with Different Motor Drive Types DeviceNet to Motor Drives Edit Menu MAC ID of DN3000 Motor Drive Type Configuring Port # 2 Motor DrivesMinimum Delay Between Messages Data Configuration Use Command Block Input Data Size Output Data Table Parameter Number Motor Drive AddressInput Data Table Use Input Word Number Word Returned Parameter Data read command only Word Motor Drive Address CommandNumber Word Parameter Data write command only Word Motor Drive Address Result Code CommandOperation of the Link Switch Upper Link Configuration Mitsubishi Drives OnlyException Table Mitsubishi Drives Only Transferring Project Files Transferring Project FilesVerify Transfer OptionsDownload Project to DN3000 Upload Project from DN3000SET Directory Options SettingsOptions Settings Current Directory Path Graphic Area SET COM Port Save Options to Disk Default OptionsSET Printer Options Load Options from DiskTechnical Information Power RequirementsPhysical Dimensions Switch # Normal Off Configuration Diagnostic DIP Switch SettingsVisual LED Indicators Flashes followed by a pause DN-3000 Troubleshooting InformationFlashes followed by a pause Invalid DIP Switch Setting Protocols Supported Registers AccessedApplication Notes PLCs and Devices ALLEN-BRADLEY PLC 5, SLC500 and Micrologix PlcsLink Adapter Requirement Idec MICRO-3 PlcsIdec FA Series Plcs Koyo / PLC Direct 205 Series Plcs Memory Address PLC Registers AccessedKoyo / PLC Direct / TI 305 Series Plcs RTS Control Mitsubishi FX Series PlcsModicon Plcs and Modbus Devices Omron PlcsPass-Through Port Protocol InformationPassthrough Port Note Square D Model 100-700 PlcsWestinghouse Plcs Toshiba EX and M Series PlcsToshiba T Series Plcs Drive Parameter Numbers Assigned By Panel-Tec Application Notes Motor DrivesBaldor Motor Drives Drive Addresses Assigned By Panel-Tec Configuring a Baldor Drive For Serial CommunicationsYaskawa Motor Drives Configuring a Woods Drive For Serial CommunicationsMitsubishi Motor Drives Woods Motor DrivesDN3000 Configuration Cable Cable DiagramsSolder End Allen BradleyGE Fanuc DN3000 GE Fanuc 90/20, 30Idec Koyo/PLC Direct Mitsubishi Mitsubishi FX SeriesModicon ModiconHost Link OmronSiemens S7 TSX07 Square DTI5 232 Port DN3000 Simatic TI5 SeriesToshiba DN3000 ToshibaBaldor Baldor Motor DrivesMitsubishi Motor Drives Woods Motor Drives Yaskawa Motor Drives DeviceNet DN3000 DeviceNet Cable