ICP DAS USA 100-700 PLCS, DB25 Technical Information, Power Requirements, Physical Dimensions

Page 52

Technical Information

POWER REQUIREMENTS

9 - 28 VDC , 7 WATT with optional Earth Ground. A 9 VDC power supply (Part # 4000-0203) is available from Panel-Tec.

PHYSICAL DIMENSIONS

.95”

5.6”

5.54”

3.64”.95”

.62”

1.9”

6.75”

8.30” 7.485

46

Image 52

Contents DN-3000 Page Warranty & Notices WarrantyTable of Contents Application Notes Motor Drives Page Introduction IntroductionInstallation Software InstallationGeneral Information Software Information Software START-UPCreating Project Files Creating a Project FileProject Types Additional Project Menu Sub-Headings Devicenet to Plcs or Devices DeviceNet to PLCs or DevicesDevice Profile DeviceNet Host to Serial PLC with Pass-Through Connection Example ApplicationsDeviceNet Host to Multi-Dropped Serial PLCs Multiple DN-3000s with Different PLC or Device Types Configuring Port #1, Devicenet DeviceNet to PLCs or Devices Edit MenuMAC ID of DN3000 Configuring Port #2 Plcs or Devices PLC/Device ProtocolWire RS422 or RS485 Communications Configuring Port # 3 Passthrough Intermessage Time-OutData Configuration Use I/O DataUse Command Block Use DiagnosticsOutput Data Size Output DataInput Data Size Input DataOutput Data Table Use Output Word PLC/Device AddressFile Number Allen-Bradley PLCs only Register NumberInput Data Table Use Input Word PLC/DeviceAddressCommand Block DeviceNet to Motor Drives Devicenet to Motor DrivesDeviceNet Host to Serial Motor Drive DeviceNet Host to Multi-Dropped Serial Motor DrivesMultiple DN-3000s with Different Motor Drive Types DeviceNet to Motor Drives Edit Menu MAC ID of DN3000 Configuring Port # 2 Motor Drives Motor Drive TypeMinimum Delay Between Messages Data Configuration Use Command Block Input Data Size Output Data Table Motor Drive Address Parameter NumberInput Data Table Use Input Word Word Motor Drive Address Command Number Word Parameter Data write command onlyWord Motor Drive Address Result Code Command Number Word Returned Parameter Data read command onlyUpper Link Configuration Mitsubishi Drives Only Operation of the Link SwitchException Table Mitsubishi Drives Only Transferring Project Files Transferring Project FilesTransfer Options Download Project to DN3000Upload Project from DN3000 VerifyOptions Settings Options SettingsSET Directory Current Directory Path Graphic Area SET COM Port Default Options SET Printer OptionsLoad Options from Disk Save Options to DiskPhysical Dimensions Power RequirementsTechnical Information Visual LED Indicators DIP Switch SettingsSwitch # Normal Off Configuration Diagnostic Flashes followed by a pause Invalid DIP Switch Setting DN-3000 Troubleshooting InformationFlashes followed by a pause Registers Accessed Application Notes PLCs and DevicesALLEN-BRADLEY PLC 5, SLC500 and Micrologix Plcs Protocols SupportedIdec FA Series Plcs Idec MICRO-3 PlcsLink Adapter Requirement Memory Address PLC Registers Accessed Koyo / PLC Direct 205 Series PlcsKoyo / PLC Direct / TI 305 Series Plcs Mitsubishi FX Series Plcs Modicon Plcs and Modbus DevicesOmron Plcs RTS ControlProtocol Information Pass-Through PortSquare D Model 100-700 Plcs Passthrough Port NoteToshiba T Series Plcs Toshiba EX and M Series PlcsWestinghouse Plcs Baldor Motor Drives Application Notes Motor DrivesDrive Parameter Numbers Assigned By Panel-Tec Configuring a Baldor Drive For Serial Communications Drive Addresses Assigned By Panel-TecConfiguring a Woods Drive For Serial Communications Mitsubishi Motor DrivesWoods Motor Drives Yaskawa Motor DrivesCable Diagrams DN3000 Configuration CableAllen Bradley Solder EndGE Fanuc 90/20, 30 GE Fanuc DN3000Idec Koyo/PLC Direct Mitsubishi FX Series MitsubishiModicon ModiconOmron Host LinkSiemens S7 Square D TSX07Simatic TI5 Series TI5 232 Port DN3000Toshiba Toshiba DN3000Baldor Motor Drives BaldorMitsubishi Motor Drives Woods Motor Drives Yaskawa Motor Drives DeviceNet Cable DeviceNet DN3000