Edimax Technology Wireless Broadband Router manual Type in this MAC address in this section or use

Page 24

 

Type in this MAC address in this section or use the

 

"Clone MAC Address" button to replace the WAN

 

MAC address with the MAC address of that PC

 

(you have to be using that PC for the Clone MAC

 

Address button to work). To find out the PC's MAC

 

address see Appendix A. (see Glossary for an

 

explanation on MAC address)

Use the following

The ISP gives you a static IP to be used

IP address

to connect to the L2TP server.

IP Address

This is the IP address that your ISP has given you to

 

establish a L2TP connection.

Subnet Mask

Enter the Subnet Mask provided by your ISP (e.g.

 

255.255.255.0)

Gateway

Enter the IP address of the ISP Gateway

User ID

Enter the User Name provided by your ISP for the

 

PPTP connection. Sometimes called a Connection ID

Password

Enter the Password provided by your ISP for the

 

PPTP connection

L2TP Gateway

If your LAN has a L2TP gateway, then enter that

 

L2TP gateway IP address here. If you do not have a

 

L2TP gateway then enter the ISP’s Gateway IP

 

address above

MTU

This is optional. You can specify the maximum size of

 

your transmission packet to the Internet. Leave it as it

 

is if you to not wish to set a maximum packet size.

Connection Type

If you select “Continuous”, the router will always

 

connect to the ISP. If the WAN line breaks down and

 

links again, the router will auto-reconnect to the ISP.

 

If you select “Connect On Demand”, the router will

 

auto-connect to the ISP when someone want to use

 

the Internet and keep connected until the WAN idle

 

timeout. The router will close the WAN connection if

 

the time period that no one is using the Internet

 

exceeds the “Idle Time”.

 

23

Image 24
Contents User’s Manual Page NAT Features Package ContentMinimum Requirements Reset Get to know the Broadband Router Back PanelLocal Area Network LAN Wide Area Network WANFront Panel Light Status DescriptionSetup Diagram Configure your PC to obtain an IP address automaticallyGetting started DNS Configuration Select Disable DNS 2b Windows XP 2c Windows 2d Windows NT IP Address Select Obtain an IP address from a Dhcp serverPage Quick Setup Wizard Chapter General Setup ChapterQuick Setup Status Info. ChapterSystem Tools Chapter Time ZoneBroadband Type Pptp L2TPCable Modem Fixed-IP xDSL DNSPPPoE MTU Pptp BEZEQ-ISRAEL L2TP Type in this MAC address in this section or use Turn OFF the Router When YOU Finished Using the Internet Telstra Big PondGeneral Settings WAN LANNAT SystemTime Zone Password Settings Remote Management WAN Page Wireless ISP Dynamic IPStatic IP Address PPPoE PPP over Ethernet8 DNS Ddns LAN LAN IPFrom network loop happened Wireless Basic SettingsSetting Essid Wlan MACAdvanced Settings Page Iapp SecurityWEP only 3.2 802.1x only 3.3 802.1x WEP Static key WPA Pre-shared keyWpatkip WPA2AESWPA Radius Access Control QoS Page Edit QoS Rule Will apply to. You can assign a single port number NAT Port Forwarding Page Virtual Server Page Example Virtual Server Special ApplicationsPage Example Special Applications ExampleUPnP Settings ALG Settings Static Routing Firewall Access Control Rule for users by IP addresses Add PC Client PC Service Example Access ControlURL Blocking DoS Denial of Service Intrusion Detection Feature4 DMZ Status Status and Information Internet Connection Primary DNS and Secondary DNS being usedDevice Status System Log Security Log Active Dhcp Client Statistics Tool Configuration Tools Restore to Factory Defaults tool to forceFirmware Upgrade Perform a reset. Your settings will not be Appendix a How to Manually find your PC’s IP and MAC address Glossary Page TCP FTP Smtp POP3 TCPSnmp UCP UDP