Edimax Technology Wireless Broadband Router Will apply to. You can assign a single port number

Page 53

Bandwidth

You can assign the download or upload bandwidth by

 

the unit of Kbps (1024 bit per second). You can limit

 

the maximum bandwidth consumed by this rule by

 

selecting “Maximum”. You also can reserve enough

 

bandwidth for this rule by selecting “Guarantee”.

Local IP Address

Enter the local IP address range of the packets that

 

this rule will apply to. If you assign 192.168.2.3 –

 

192.168.2.5, it means 3 IP addresses: 192.168.2.3,

 

192.168.2.4 and 192.168.2.5

Local Port Range

Enter the local port range of the packets that this rule

 

will apply to. You can assign a single port number

 

here or assign a range of port numbers by assigning

 

the first port number and the last port number of the

 

range. The two numbers are separated by a dash “-“,

 

for example “101-150” means from port number 100

 

to port number 150 – the range of 50 port numbers.

Remote IP Address

Enter the remote IP address range of the packets

 

that this rule will apply to. If you assign 192.168.2.3 –

 

192.168.2.5, it means 3 IP addresses: 192.168.2.3,

 

192.168.2.4 and 192.168.2.5

Remote Port Range

Enter the remote port range of the packets that this

 

rule will apply to. You can assign a single port

 

number here or assign a range of port numbers by

 

assigning the first port number and the last port

 

number of the range. The two numbers are separated

 

by a dash “-“, for example “101-150” means from port

 

number 100 to port number 150 – the range of 50

 

port numbers.

Traffic Type

Select the traffic type of the packets that this rule will

 

apply to. We list some popular applications here to

 

ease the configuration. You also can get the same

 

result by using other parameters, for example source

 

or destination port number, if you are familiar with the

 

application protocol.

Protocol

Select the protocol type of the packets that this rule

 

will apply to.

Apply

Apply and exit the form.

 

52

Image 53
Contents User’s Manual Page NAT Minimum Requirements FeaturesPackage Content Get to know the Broadband Router Back Panel ResetLocal Area Network LAN Wide Area Network WANLight Status Description Front PanelGetting started Setup DiagramConfigure your PC to obtain an IP address automatically DNS Configuration Select Disable DNS 2b Windows XP 2c Windows IP Address Select Obtain an IP address from a Dhcp server 2d Windows NTPage General Setup Chapter Quick Setup Wizard ChapterStatus Info. Chapter Quick SetupSystem Tools Chapter Time ZoneBroadband Type L2TP PptpCable Modem DNS Fixed-IP xDSLPPPoE MTU Pptp BEZEQ-ISRAEL L2TP Type in this MAC address in this section or use Telstra Big Pond Turn OFF the Router When YOU Finished Using the InternetGeneral Settings LAN WANSystem NATTime Zone Password Settings Remote Management WAN Page Dynamic IP Wireless ISPStatic IP Address PPPoE PPP over Ethernet8 DNS Ddns LAN IP LANFrom network loop happened Setting WirelessBasic Settings Wlan MAC EssidAdvanced Settings Page Security IappWEP only 3.2 802.1x only WPA Pre-shared key 3.3 802.1x WEP Static keyWPA2AES WpatkipWPA Radius Access Control QoS Page Edit QoS Rule Will apply to. You can assign a single port number NAT Port Forwarding Page Virtual Server Page Special Applications Example Virtual ServerPage Example Example Special ApplicationsUPnP Settings ALG Settings Static Routing Firewall Access Control Rule for users by IP addresses Add PC Example Access Control Client PC ServiceURL Blocking Intrusion Detection Feature DoS Denial of Service4 DMZ Status Status and Information Primary DNS and Secondary DNS being used Internet ConnectionDevice Status System Log Security Log Active Dhcp Client Statistics Tool Restore to Factory Defaults tool to force Configuration ToolsFirmware Upgrade Perform a reset. Your settings will not be Appendix a How to Manually find your PC’s IP and MAC address Glossary Page TCP TCP FTP Smtp POP3Snmp UCP UDP