Edimax Technology Wireless Broadband Router Wireless ISP, Dynamic IP, Static IP Address, 6 L2TP

Page 34

Once you have made a selection, click <More Configuration> at the bottom of the screen and proceed to the manual’s relevant sub-section

2.2.1 Wireless ISP

Choose the the “WAN Type”, “Wireless ISP” and “Apply” button for connecting to the wireless Access Point and proceed to the manual’s relevant sub-section.

Once you have made a selection, click <More Configuration> at the bottom of the screen and proceed to the manual’s relevant sub-section

2.2.2 Dynamic IP

Choose the Dynamic IP selection if your ISP will automatically give you an IP address. Some ISP’s may also require that you fill in additional information such as Host Name, Domain Name and MAC address (see chapter 1 “Cable Modem” for more detail)

2.2.3 Static IP Address

Select Static IP address if your ISP has given you a specific IP address for you to use. Your ISP should provide all the information required in this section. (See chapter 1 “Fixed IP” for more detail)

.2.2.4 PPPoE (PPP over Ethernet)

Select PPPoE if your ISP requires the PPPoE protocol to connect you to the Internet. Your ISP should provide all the information required in this section. (See chapter 1 “PPPoE” for more detail)

2.2.5 PPTP

Select PPTP if your ISP requires the PPTP protocol to connect you to the Internet. Your ISP should provide all the information required in this section. (See chapter 1 “PPTP” for more detail)

2.2.6 L2TP

Select L2TP if your ISP requires the L2TP protocol to connect you to the Internet. Your ISP should provide all the information required in this section. (See chapter 1 “L2TP” for more detail)

2.2.7 Telstra Big Pond

Select Telstra Big Pond if your ISP requires the Telstra Big Pond protocol to connect you to the Internet. Your ISP should provide all the information required in this section. Telstra Big Pond protocol is used by the ISP in Australia. (See chapter 1 “Telstra Big Pond” for more detail)

33

Page 33 Page 35
Image 34
Page 33 Page 35
Contents User’s Manual Page NAT Package Content FeaturesMinimum Requirements Local Area Network LAN ResetGet to know the Broadband Router Back Panel Wide Area Network WANFront Panel Light Status DescriptionConfigure your PC to obtain an IP address automatically Setup DiagramGetting started DNS Configuration Select Disable DNS 2b Windows XP 2c Windows 2d Windows NT IP Address Select Obtain an IP address from a Dhcp serverPage Quick Setup Wizard Chapter General Setup ChapterSystem Tools Chapter Quick SetupStatus Info. Chapter Time ZoneBroadband Type Pptp L2TPCable Modem Fixed-IP xDSL DNSPPPoE MTU Pptp BEZEQ-ISRAEL L2TP Type in this MAC address in this section or use Turn OFF the Router When YOU Finished Using the Internet Telstra Big PondGeneral Settings WAN LANNAT SystemTime Zone Password Settings Remote Management WAN Page Static IP Address Wireless ISPDynamic IP PPPoE PPP over Ethernet8 DNS Ddns LAN LAN IPFrom network loop happened Basic Settings WirelessSetting Essid Wlan MACAdvanced Settings Page Iapp SecurityWEP only 3.2 802.1x only 3.3 802.1x WEP Static key WPA Pre-shared keyWpatkip WPA2AESWPA Radius Access Control QoS Page Edit QoS Rule Will apply to. You can assign a single port number NAT Port Forwarding Page Virtual Server Page Example Virtual Server Special ApplicationsPage Example Special Applications ExampleUPnP Settings ALG Settings Static Routing Firewall Access Control Rule for users by IP addresses Add PC Client PC Service Example Access ControlURL Blocking DoS Denial of Service Intrusion Detection Feature4 DMZ Status Status and Information Internet Connection Primary DNS and Secondary DNS being usedDevice Status System Log Security Log Active Dhcp Client Statistics Tool Configuration Tools Restore to Factory Defaults tool to forceFirmware Upgrade Perform a reset. Your settings will not be Appendix a How to Manually find your PC’s IP and MAC address Glossary Page Snmp UCP TCP FTP Smtp POP3TCP UDP
Top Page Image Contents