Briggs & Stratton 071013 manual Important Safety Instructions

Page 3

SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

The safety alert symbol () is used with a signal word (DANGER, CAUTION,WARNING), a pictorial and/or a safety message to alert you to hazards. DANGER indicates a hazard which, if not avoided, will result in death or serious injury. WARNING indicates a hazard which, if not avoided, could result in death or serious injury. CAUTION indicates a hazard which, if not avoided, might result in minor or moderate injury. CAUTION, when used without the alert symbol, indicates a situation that could result in equipment damage. Follow safety messages to avoid or reduce the risk of injury or death.

The manufacturer cannot possibly anticipate every possible circumstance that might involve a hazard.The warnings in this manual, and the tags and decals affixed to the unit are, therefore, not all-inclusive. If you use a procedure, work method or operating technique that the manufacturer does not specifically recommend, you must satisfy yourself that it is safe for you and others.You must also make sure that the procedure, work method or operating technique that you choose does not render the power management system unsafe.

WARNING

Only qualified electricians should attempt installation

of this system, which must strictly comply with applicable codes, standards and regulations.

WARNING

Low voltage wire cannot be installed in same conduit as power voltage wiring.

Failure to follow above warning could cause personal injury, damage and/or malfunction of equipment.

WARNING

Failure to properly ground power management system can result in electrocution.

DO NOT touch bare wires.

DO NOT use power management system with worn, frayed, bare or otherwise damaged wiring.

DO NOT handle electrical cords while standing in water, while barefoot, or while hands or feet are wet.

If you must work around a unit while it is operating, stand on an insulated dry surface to reduce shock hazard.

DO NOT allow unqualified persons or children to operate or service power management system.

In case of an accident caused by electrical shock, immediately shut down all sources of electrical power and contact local authorities. Avoid direct contact with the victim.

WARNING

Power management system contains high voltage that can cause personal injury or death.

Despite the safe design of the power management system, operating this equipment imprudently, neglecting its maintenance or being careless can cause possible injury or death.

CAUTION

Improper treatment of power management system can damage it and shorten its life.

Use power management system only for intended uses.

If you have questions about intended use, ask dealer or contact Briggs and Stratton Power Products.

DO NOT expose power management system to excessive moisture, dust, dirt, or corrosive vapors.

Remain alert at all times while working on this equipment. NEVER work on the equipment when you are physically or mentally fatigued.

If connected devices overheat, turn them off and turn off their circuit breaker/fuse.

3

Image 3
Contents Installation Operator’s Manual Table of Contents Use power management system only for intended uses Important Safety InstructionsFor the Installing Dealer/Contractor IntroductionFor the Home Owner Installer Responsibilities Owner OrientationEquipment Description Installation UnpackingMounting Guidelines Power Wiring Interconnections Typical Installation Diagram for Power Management System System SetupWiring Decal System Operation SpecificationsTesting the Power Management System When Calling the FactoryProblem Cause Correction TroubleshootingElectrical Load Worksheet MANUAL, Load Control Center Exploded View & Parts ListWASHER, Shakeproof, Ext M6 1/4 DECAL,WarningPage Warranty Period Mise À Lessai DU Système DE Gestion DE Lalimentation Table DES MatièresAvertissement Directives DE Sécurité ImportantesAu Détaillant ou à lEntrepreneur Procédant à lInstallation IntroductionAu Propriétaire Résidentiel Vérifiez tous les codes fédéraux, provinciaux et locaux Responsabilités de lInstallateurConseils au Propriétaire Description de lÉquipementDéballage InstallationConsignes dinstallation Dinstallation du système de gestion de l’alimentationLes connecteurs de fils fournis Interconnexions du câblage dalimentationModule de commande Configuration du systèmeDécalcomanie Dinstallation Éléctrique Si vous Devez Communiquer avec lUsine CaractéristiquesFonctionnement Mise À Lessai DU Système DE Gestion DE LalimentationDu climatiseur est expiré DépannageDes terminaux De verrouillage est expiréFiche Technique DE Charge Électrique Période DE Garantie Tabla DE Contenido Instrucciones Importantes DE Seguridad AdvertenciaPrecaución Para el Propietario Doméstico IntroducciónLea y cumpla las instrucciones incluidas en el manual Orientación para el PropietarioResponsabilidades del Instalador Descripción del EquipoInstalación DesempaquePautas de Montaje Conecte el terminal GND a una toma de tierra aprobada Interconexiones de Cableado de EnergíaConfiguración del Sistema PosicionesConmutador Alambrar LA Calcomanía Si Necesita Llamar a Fábrica EspecificacionesSistema Funcionamiento Prueba DEL Sistema DE Gestión DE Energía EléctricaReparacion DE Averias Hoja DE Trabajo DE Cargas Eléctricas Notas Período DE Garantía