Briggs & Stratton 071013 Introduction, For the Home Owner, For the Installing Dealer/Contractor

Page 4

INTRODUCTION

INTRODUCTION

Thank you for your purchase of this Briggs & Stratton Power Management System.This product is intended for use with Briggs & Stratton Automatic Transfer Switches and Home Standby Generators ONLY.This is an optional automated system that will control the distribution of power from a home standby system (generator) to selected household loads.

Briggs and Stratton (B&S) has made every effort to provide for a safe, streamlined and cost-effective installation. As each installation is unique, it is impossible to know of and advise of all conceivable procedures and methods by which installation might be achieved.We do not know all possible hazards and/or the results of each method or procedure. For these reasons,

Only licensed electrical contractors should install power management systems. Installations must strictly comply with all applicable federal, state and local codes, standards and regulations.

Your B&S power management system is supplied with this combined “Installation and Operator’s Manual”.This is an important document and should be retained by the owner after the installation has been completed.

Every effort has been expended to make sure that the information in this manual is both accurate and current. However, the manufacturer reserves the right to change, alter or otherwise improve the system at any time without prior notice.

For the Home Owner

To help you make informed choices and communicate effectively with your installation contractor(s),

Read and understand the

Owner Orientation Section of this manual

BEFORE contracting or starting

your power management system installation.

To arrange for proper installation, contact the store at which you purchased your B&S power management system, your dealer, or your utility power provider.

The power management system warranty is VOID unless the system is installed

by a licensed electrical professional.

For the Installing Dealer/Contractor

Check federal, state and local codes for questions on installation.

If you need more information about the power management system, call 1-800-743-4115, between 8:00 AM and 5:00 PM CT.

4

Image 4
Contents Installation Operator’s Manual Table of Contents Important Safety Instructions Use power management system only for intended usesIntroduction For the Installing Dealer/ContractorFor the Home Owner Owner Orientation Installer ResponsibilitiesEquipment Description Unpacking InstallationMounting Guidelines Power Wiring Interconnections System Setup Typical Installation Diagram for Power Management SystemWiring Decal Specifications Testing the Power Management SystemWhen Calling the Factory System OperationTroubleshooting Problem Cause CorrectionElectrical Load Worksheet Exploded View & Parts List WASHER, Shakeproof, Ext M6 1/4DECAL,Warning MANUAL, Load Control CenterPage Warranty Period Table DES Matières Mise À Lessai DU Système DE Gestion DE LalimentationDirectives DE Sécurité Importantes AvertissementIntroduction Au Détaillant ou à lEntrepreneur Procédant à lInstallationAu Propriétaire Résidentiel Responsabilités de lInstallateur Conseils au PropriétaireDescription de lÉquipement Vérifiez tous les codes fédéraux, provinciaux et locauxInstallation Consignes dinstallationDinstallation du système de gestion de l’alimentation DéballageInterconnexions du câblage dalimentation Les connecteurs de fils fournisConfiguration du système Module de commandeDécalcomanie Dinstallation Éléctrique Caractéristiques FonctionnementMise À Lessai DU Système DE Gestion DE Lalimentation Si vous Devez Communiquer avec lUsineDépannage Des terminauxDe verrouillage est expiré Du climatiseur est expiréFiche Technique DE Charge Électrique Période DE Garantie Tabla DE Contenido Advertencia Instrucciones Importantes DE SeguridadPrecaución Introducción Para el Propietario DomésticoOrientación para el Propietario Responsabilidades del InstaladorDescripción del Equipo Lea y cumpla las instrucciones incluidas en el manualDesempaque InstalaciónPautas de Montaje Interconexiones de Cableado de Energía Conecte el terminal GND a una toma de tierra aprobadaPosiciones Configuración del SistemaConmutador Alambrar LA Calcomanía Especificaciones Sistema FuncionamientoPrueba DEL Sistema DE Gestión DE Energía Eléctrica Si Necesita Llamar a FábricaReparacion DE Averias Hoja DE Trabajo DE Cargas Eléctricas Notas Período DE Garantía