Maxon Telecom MM-6280IND manual Auto delete Messages in ME Memory, SMS Notifications

Page 48

9.1.2.Auto delete Messages in ME Memory

9.1.2.1.Auto Delete Messages in ME memory($$AUTO_DLTSMS)

Table 9-55 Read command

	Command			TE2	Æ		MT2	$$AUTO_DLTSMS
	Response			TE2	Å		MT2	$$SMSNOTIF: <value>
	Value			0: Auto delete is turned off
	Value			1: Auto delete is turned on
				1: Auto delete is turned on
	Table 9-56 Set command
	Command			TE2	Æ		MT2	$$AUTO_DLTSMS=<value>
	Response			TE2	Å		MT2	<result_code> (OK ERROR)

9.1.3.SMS Notifications

9.1.3.1.SMS Notification ($$SMSNOTIF)

Table 9-57 Read command

	Command			TE2		Æ		MT2	$$SMSNOTIF?
	Response			TE2		Å		MT2	$$SMSNOTIF: <value>
	Value			0: No Alert
	Value			1: Alert
				1: Alert
	Table 9-58 Set command
	Command			TE2		Æ		MT2	$$SMSNOTIF=<value>
	Response			TE2		Å		MT2	<result_code> (OK ERROR)

Extended AT Commands Manual

Page 48 of 70

2009-06-25

Image 48

Contents Extended AT Commands Manual RF Exposure Compliance Potentially Unsafe AreasRevision History Contact Information TA BLE of Contents 1.3 2.1 Carrier Command Options Overview General DescriptionTerms Pstn RCESMS TE2AT Inte Rface Description Basic IntegrationSerial Interface Pin outCommand Format Message Naming ConventionBasic Interface Configuration Baud Rate Set-upUSB Interface TE2 MT2IO Functions AT Notification OptionsTE2 MT2 $$IOFUNCTION? TE2 MT2 $$NOTIFCNT?Set command Command $$NOTIFCNT=value$$NOTIFCNT 1 0 Success Failure Signal Information MT SMSMT Data Boot alert Interface EnvironmentMT2 Basic Operational State Lock order1.4. TE2 active command AT$$TE2ALIVE Power Reset AT$$RESETPower Conservation Commands Sleep mode control AT$$SLEEPENABLECurrent time AT$$TIME Software version AT$$SWVERExtended AT Commands Manual 2009-06-25 Low Battery Voltage Notification 1.3. RS232C Transceiver power-down control AT$$RS232PWRDOWNLED control AT$$EXTLED TE2 MT2 $$EXTLED?SMS low battery voltage set point AT$$LOWBATTVTG Low battery notification AT$$LOWBATTTE2 MT2 $$LOWBATTVTG? Receiving notification mode option AT$$RCVMODE Ringer volume control AT$$RINGLVLVisual/Audible Call Alert Options Ringer melody selection AT$$RINGIDXNetwork Relational Settings Roaming indicator information AT$$ROAMINDAntenna Signal Level report schedule AT$$ANTSET Antenna Signal Level AT$$ANTLVLModem scheduled Information AT$$Ping Rssi inquiry AT$$RSSIReading MT2 state AT$$CURRSTATE RF information AT$$RFINFO Location information AT$$LOCATIONTE2 MT2 $$LOCATION? Diagnostic Commands Ring test AT$$DIAGRINGLED test AT$$DIAGLED Rssi LED response AT$$RSSILEVELLed Description CRTPKT TX/DTRData Call SET UP Data CallsCall released or failed Uses DTR pin MO data callGeneral Configuration Commands Select Message Service +CSMS+CSMS action command syntax Preferred Message Storage +CPMSMessage Service Failure Result Code +CMS Error Message Format +CMGFMessage Configuration Commands Service Centre Address +CSCAInformative Examples Set Text Mode Parameters +CSMP Show Text Mode Parameters +CSDHMessage Receiving and Reading commands New Message Indications to TE +CNMIAlpha,scts,tooa,fo,pid,dcs,sca,tosca List Messages +CMGL If text mode +CMGF=1, command successful and SMS-DELIVER If text mode +CMGF=1, command successful and SMS-SUBMITRead Message +CMGR New Message Acknowledgement to ME/TA +CNMA ReportMessage Sending and Writing Commands Send Message +CMGSIf text mode +CMGF=1 If text mode +CMGF=1 and sending Send Message from Storage +CMSSSuccessful If sending failsSend Message Telstra SMS MO AT+MMC Write Message to Memory +CMGWSend Command +CMGC Delete Message +CMGDMore Messages to Send +CMMS AT+CNMI? AT+CMSS=7 SMS Send and Receive Options SMS Mail Notification Option SMSOPT=ABSMS Format send and receiveAT$$SMSOPT TE2 MT2 $$SMSOPT?SMS Mail Notification Option SMSOPT=1 SMS Mail Notification Option SMSOPT=2SMS Mail Notification Option SMSOPT=3 Illustrative exampleAuto delete Messages in ME Memory SMS NotificationsAuto Delete Messages in ME memory$$AUTODLTSMS SMS Notification $$SMSNOTIFSMS Auto Voltage Alert Auto Voltage Alert SMS Site Name AT$$SITENAMESMS $$LOWBATT 1 set point AT$$LOWBATTVTG TE2 MT2 $$SITENAME?SMS Remote Report Requests SMS $$LOWBATT 1 set recipient number AT$$AUTOSMSSMS Remote Report Request Site Name AT$$REMOTECTRL Read ALL request Vbatt request10.1.2.4 Rssi request Location request Swver requestDebug Screen request Remote Reset 73 Read command Enter directory number of specific MT2Enter message maxon.reset not case sensitive Value Modem will resetCommand User Remarks Profile NVM vs . US ER PR Ofile StorageTIA/EIA/IS 707A AT Command SET TE2 MT2 OK ErrorUser modified profiles & NVM changes User Profile store AT&WnBasic AT Commands Basic AT ParametersSTU IIIBasic S registers Basic action command set Extended AT Commands Manual 2009-06-25 Extended AT Command Sets Extended AT configuration command setBasic result codes +GCAP +GMI+GMM +GMR8Data 1Stop Default Space Default+ICF Circuit 133 Ready for Receiving Default Circuit 106 Clear to Send/Ready for Sending Default+IFC 115200bps. Default +IPR13.1.1. RM3 AT$$NOTIDS TE2 MT2 $$NOTIDS?TE2 MT2 $$NOTIDS Cellular Extended AT Command SET Cellular AT parameter commands+CDS +CBC?Cellular identification AT command extensions +CGMI+CGMM +CGMRCellular result codes for Asynchronous data services DM Comman D Diagnostic Mode Carrier Command Options Debug screen AT$$DBGSCRNTE2 MT2 $$DBGSCRN

Related manuals

Manual 60 pages 51.94 Kb