Maxon Telecom MM-6280IND manual Signal Information, Mt Sms, MT Data

Page 17

4 . SIGNAL INFORMATION

4.1. MT SMS

Table 4-10

Status	Signal	Action
	AT	SMS Notification to Serial and USB ports

		$$SMSNOTIF value “0”: No alert
Idle,		$$SMSNOTIF value “1”: Buzzer alerts 4 times initially only
Data	Buzzer	$$SMSNOTIF value “2”: Buzzer alerts 4 times initially followed by
		once every two sec.
		$$SMSNOTIF value “3”: Buzzer alerts 4 times initially only

4.2. MT DATA

Table 4-11

Signal	Action
AT	‘RING’ notification
Ring Buzzer	Audible Ring (excepting where $$RCV_MODE is 1)

Extended AT Commands Manual

Page 17 of 70

2009-06-25

Image 17

Contents Extended AT Commands Manual Potentially Unsafe Areas RF Exposure ComplianceRevision History Contact Information TA BLE of Contents 1.3 2.1 Carrier Command Options General Description OverviewTerms RCE PstnSMS TE2Basic Integration AT Inte Rface DescriptionSerial Interface Pin outMessage Naming Convention Command Format Baud Rate Set-up Basic Interface Configuration USB Interface TE2 MT2AT Notification Options IO FunctionsTE2 MT2 $$IOFUNCTION? TE2 MT2 $$NOTIFCNT?$$NOTIFCNT 1 0 Success Failure Set command Command$$NOTIFCNT=value MT Data Signal InformationMT SMS Interface Environment Boot alertMT2 Basic Operational State Lock orderPower Reset AT$$RESET 1.4. TE2 active command AT$$TE2ALIVESleep mode control AT$$SLEEPENABLE Power Conservation CommandsCurrent time AT$$TIME Software version AT$$SWVERExtended AT Commands Manual 2009-06-25 1.3. RS232C Transceiver power-down control AT$$RS232PWRDOWN Low Battery Voltage NotificationLED control AT$$EXTLED TE2 MT2 $$EXTLED?TE2 MT2 $$LOWBATTVTG? SMS low battery voltage set point AT$$LOWBATTVTGLow battery notification AT$$LOWBATT Ringer volume control AT$$RINGLVL Receiving notification mode option AT$$RCVMODEVisual/Audible Call Alert Options Ringer melody selection AT$$RINGIDXRoaming indicator information AT$$ROAMIND Network Relational SettingsAntenna Signal Level report schedule AT$$ANTSET Antenna Signal Level AT$$ANTLVLReading MT2 state AT$$CURRSTATE Modem scheduled Information AT$$PingRssi inquiry AT$$RSSI TE2 MT2 $$LOCATION? RF information AT$$RFINFOLocation information AT$$LOCATION Ring test AT$$DIAGRING Diagnostic CommandsLED test AT$$DIAGLED Rssi LED response AT$$RSSILEVELCRT Led DescriptionPKT TX/DTRData Calls Data Call SET UPCall released or failed Uses DTR pin MO data callSelect Message Service +CSMS General Configuration Commands+CSMS action command syntax Preferred Message Storage +CPMSMessage Format +CMGF Message Service Failure Result Code +CMS ErrorInformative Examples Message Configuration CommandsService Centre Address +CSCA Show Text Mode Parameters +CSDH Set Text Mode Parameters +CSMPNew Message Indications to TE +CNMI Message Receiving and Reading commandsAlpha,scts,tooa,fo,pid,dcs,sca,tosca List Messages +CMGL Read Message +CMGR If text mode +CMGF=1, command successful and SMS-DELIVERIf text mode +CMGF=1, command successful and SMS-SUBMIT Report New Message Acknowledgement to ME/TA +CNMASend Message +CMGS Message Sending and Writing CommandsSend Message from Storage +CMSS If text mode +CMGF=1 If text mode +CMGF=1 and sendingSuccessful If sending failsWrite Message to Memory +CMGW Send Message Telstra SMS MO AT+MMCDelete Message +CMGD Send Command +CMGCAT+CNMI? More Messages to Send +CMMSAT+CMSS=7 SMS Mail Notification Option SMSOPT=AB SMS Send and Receive OptionsSMS Format send and receiveAT$$SMSOPT TE2 MT2 $$SMSOPT?SMS Mail Notification Option SMSOPT=2 SMS Mail Notification Option SMSOPT=1SMS Mail Notification Option SMSOPT=3 Illustrative exampleSMS Notifications Auto delete Messages in ME MemoryAuto Delete Messages in ME memory$$AUTODLTSMS SMS Notification $$SMSNOTIFAuto Voltage Alert SMS Site Name AT$$SITENAME SMS Auto Voltage AlertSMS $$LOWBATT 1 set point AT$$LOWBATTVTG TE2 MT2 $$SITENAME?SMS Remote Report Request Site Name AT$$REMOTECTRL SMS Remote Report RequestsSMS $$LOWBATT 1 set recipient number AT$$AUTOSMS 10.1.2.4 Rssi request Read ALL requestVbatt request Debug Screen request Location requestSwver request 73 Read command Enter directory number of specific MT2 Remote ResetEnter message maxon.reset not case sensitive Value Modem will resetNVM vs . US ER PR Ofile Storage Command User Remarks ProfileTE2 MT2 OK Error TIA/EIA/IS 707A AT Command SETUser modified profiles & NVM changes User Profile store AT&WnBasic AT Parameters Basic AT CommandsSTU IIIBasic S registers Basic action command set Extended AT Commands Manual 2009-06-25 Basic result codes Extended AT Command SetsExtended AT configuration command set +GMI +GCAP+GMM +GMR+ICF 8Data 1Stop DefaultSpace Default +IFC Circuit 133 Ready for Receiving DefaultCircuit 106 Clear to Send/Ready for Sending Default +IPR 115200bps. DefaultTE2 MT2 $$NOTIDS 13.1.1. RM3 AT$$NOTIDSTE2 MT2 $$NOTIDS? Cellular AT parameter commands Cellular Extended AT Command SET+CDS +CBC?+CGMI Cellular identification AT command extensions+CGMM +CGMRCellular result codes for Asynchronous data services DM Comman D Diagnostic Mode TE2 MT2 $$DBGSCRN Carrier Command OptionsDebug screen AT$$DBGSCRN

Related manuals

Manual 60 pages 51.94 Kb