Maxon Telecom MM-6280IND Message Format +CMGF, Message Service Failure Result Code +CMS Error

Page 32

Table 24. +CPMS action command syntax

Command	Possible response(s)
+CPMS=<mem1
>[,	+CPMS: <used1>,<total1>,<used2>,<total2>,<used3>,<total3>
<mem2>[,<me	+CMS ERROR: <err>
m3>]]
+CPMS?	+CPMS: <mem1>,<used1>,<total1>,<mem2>,<used2>,<total2>,
+CPMS?	<mem3>,<used3>,<total3>
	+CMS ERROR: <err>
+CPMS=?	+CPMS: (list of supported <mem1>s),(list of supported <mem2>s),
	(list of supported <mem3>s)

8.1.1.3.Message Format +CMGF

Set command tells the TA, which input and output format of messages to use. <mode> indicates the format of messages used with send, list, read and write commands and unsolicited result codes resulting from received messages. Mode can be either PDU mode (entire TP data units used) or text mode (headers and body of the messages given as separate parameters). Text mode uses the value of parameter <chset> specified by command Select TE C haracter Set +CSCS to inform the character set to be used in the message body in the TA-TE interface.

Test command returns supported modes as a compound value.

Table 3. +CMGF action command syntax

	Command		Possible response(s)
	+CMGF=[mode	+CMGF: mode
	]	+CMGF: mode
	]
	+CMGF?	+CMGF: mode
	+CMGF=?	+CMGF: (list of supported <mode>s)
	Value	<mode>
	Value	0	: PDU mode (default when implemented)
		1	: text mode

8.1.1.4.Message Service Failure Result Code +CMS ERROR

Final result code +CMS ERROR: <err> indicates an error related to mobile equipment or network. The operation is similar to ERROR result code. None of the following commands in the same command line is executed. Neither ERROR nor OK result code shall be returned. ERROR is returned normally when error is related to syntax or invalid parameters.

Table 4. <err> values used by common messaging commands:

value		Description
0...127	3GPP TS 24.011	clause E.2 values
128...255	3GPP TS 23.040	clause 9.2.3.22 values.
300	ME failure
301	SMS service of ME reserved
302	operation not allowed
303	operation not supported
Extended AT Commands Manual		Page 32 of 70	2009-06-25

Image 32

Contents Extended AT Commands Manual RF Exposure Compliance Potentially Unsafe AreasRevision History Contact Information TA BLE of Contents 1.3 2.1 Carrier Command Options Overview General DescriptionTerms Pstn RCESMS TE2AT Inte Rface Description Basic IntegrationSerial Interface Pin outCommand Format Message Naming ConventionBasic Interface Configuration Baud Rate Set-upUSB Interface TE2 MT2IO Functions AT Notification OptionsTE2 MT2 $$IOFUNCTION? TE2 MT2 $$NOTIFCNT?$$NOTIFCNT 1 0 Success Failure Set command Command$$NOTIFCNT=value MT Data Signal InformationMT SMS Boot alert Interface EnvironmentMT2 Basic Operational State Lock order1.4. TE2 active command AT$$TE2ALIVE Power Reset AT$$RESETPower Conservation Commands Sleep mode control AT$$SLEEPENABLECurrent time AT$$TIME Software version AT$$SWVERExtended AT Commands Manual 2009-06-25 Low Battery Voltage Notification 1.3. RS232C Transceiver power-down control AT$$RS232PWRDOWNLED control AT$$EXTLED TE2 MT2 $$EXTLED?TE2 MT2 $$LOWBATTVTG? SMS low battery voltage set point AT$$LOWBATTVTGLow battery notification AT$$LOWBATT Receiving notification mode option AT$$RCVMODE Ringer volume control AT$$RINGLVLVisual/Audible Call Alert Options Ringer melody selection AT$$RINGIDXNetwork Relational Settings Roaming indicator information AT$$ROAMINDAntenna Signal Level report schedule AT$$ANTSET Antenna Signal Level AT$$ANTLVLReading MT2 state AT$$CURRSTATE Modem scheduled Information AT$$PingRssi inquiry AT$$RSSI TE2 MT2 $$LOCATION? RF information AT$$RFINFOLocation information AT$$LOCATION Diagnostic Commands Ring test AT$$DIAGRINGLED test AT$$DIAGLED Rssi LED response AT$$RSSILEVEL Led Description CRT PKT TX/DTRData Call SET UP Data CallsCall released or failed Uses DTR pin MO data callGeneral Configuration Commands Select Message Service +CSMS+CSMS action command syntax Preferred Message Storage +CPMSMessage Service Failure Result Code +CMS Error Message Format +CMGFInformative Examples Message Configuration CommandsService Centre Address +CSCA Set Text Mode Parameters +CSMP Show Text Mode Parameters +CSDHMessage Receiving and Reading commands New Message Indications to TE +CNMIAlpha,scts,tooa,fo,pid,dcs,sca,tosca List Messages +CMGL Read Message +CMGR If text mode +CMGF=1, command successful and SMS-DELIVERIf text mode +CMGF=1, command successful and SMS-SUBMIT New Message Acknowledgement to ME/TA +CNMA ReportMessage Sending and Writing Commands Send Message +CMGSIf text mode +CMGF=1 If text mode +CMGF=1 and sending Send Message from Storage +CMSSSuccessful If sending failsSend Message Telstra SMS MO AT+MMC Write Message to Memory +CMGWSend Command +CMGC Delete Message +CMGDMore Messages to Send +CMMS AT+CNMI?AT+CMSS=7 SMS Send and Receive Options SMS Mail Notification Option SMSOPT=ABSMS Format send and receiveAT$$SMSOPT TE2 MT2 $$SMSOPT?SMS Mail Notification Option SMSOPT=1 SMS Mail Notification Option SMSOPT=2SMS Mail Notification Option SMSOPT=3 Illustrative exampleAuto delete Messages in ME Memory SMS NotificationsAuto Delete Messages in ME memory$$AUTODLTSMS SMS Notification $$SMSNOTIFSMS Auto Voltage Alert Auto Voltage Alert SMS Site Name AT$$SITENAMESMS $$LOWBATT 1 set point AT$$LOWBATTVTG TE2 MT2 $$SITENAME?SMS Remote Report Request Site Name AT$$REMOTECTRL SMS Remote Report RequestsSMS $$LOWBATT 1 set recipient number AT$$AUTOSMS 10.1.2.4 Rssi request Read ALL requestVbatt request Debug Screen request Location requestSwver request Remote Reset 73 Read command Enter directory number of specific MT2Enter message maxon.reset not case sensitive Value Modem will resetCommand User Remarks Profile NVM vs . US ER PR Ofile StorageTIA/EIA/IS 707A AT Command SET TE2 MT2 OK ErrorUser modified profiles & NVM changes User Profile store AT&WnBasic AT Commands Basic AT ParametersSTU IIIBasic S registers Basic action command set Extended AT Commands Manual 2009-06-25 Basic result codes Extended AT Command SetsExtended AT configuration command set +GCAP +GMI+GMM +GMR+ICF 8Data 1Stop DefaultSpace Default +IFC Circuit 133 Ready for Receiving DefaultCircuit 106 Clear to Send/Ready for Sending Default 115200bps. Default +IPRTE2 MT2 $$NOTIDS 13.1.1. RM3 AT$$NOTIDSTE2 MT2 $$NOTIDS? Cellular Extended AT Command SET Cellular AT parameter commands+CDS +CBC?Cellular identification AT command extensions +CGMI+CGMM +CGMRCellular result codes for Asynchronous data services DM Comman D Diagnostic Mode TE2 MT2 $$DBGSCRN Carrier Command OptionsDebug screen AT$$DBGSCRN

Related manuals

Manual 60 pages 51.94 Kb