Maxon Telecom MM-6280IND manual Low Battery Voltage Notification, LED control AT$$EXTLED

Page 22

5.2.1.2.LED control (AT$$EXT_LED)

This command is used for control of the LED’s on-time. Changes made to this function are written to NV memory and will be present in all profiles.

Table 5-24 Read command

 

Command

 

TE2

Æ

 

 

MT2

$$EXT_LED?

 

Response

 

TE2

Å

 

 

MT2

$$EXT_LED: <value>

 

Value

Time: 0~255 seconds (0: Continuous LED ON - Default)

 

Table 5-25 Set command

 

 

 

Command

TE2

Æ

 

 

MT2

$$EXT_LED=<value>

 

Response

 

TE2

Å

 

 

MT2

$$EXT_LED: <value>

 

 

 

 

<result_code> (OK ERROR)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.2.1.3.RS232C Transceiver power-down control (AT$$RS232_PWRDOWN)

This command is used for control of the RS232C Transceiver Power Down function. When there are no valid signal transmissions on all receiver and transmitter inputs for 30 seconds, the transceivers are shut off, reducing current draw for power conservation applications.

TE2 can activate resumption of RS232 power up via dummy AT command. MT2 activity such as MT calls or MT SMS or AT Alerts will wake RS232 from power-down and pass these to TE2.

Table 5-26 Read command

 

Command

TE2

Æ

MT2

$$RS232_PWRDOWN?

 

Response

 

TE2

Å

MT2

$$RS232_PWRDOWN: <value>

 

 

 

0: Power Down disabled (Default)

 

 

 

1: Power Down enabled. The modem should go in power save modem

 

Value

 

after 30 seconds on inactivity on the RS232. An incoming AT command,

 

 

SMS or data call should wake the modem up. The modem will not go into

 

 

 

 

 

 

sleep mode while in a packet data or circuit switched call.

 

 

 

Sleep mode will work only when modem is idle.

 

 

 

 

 

 

 

Table 5-27 Set command

 

Command

 

 

TE2

Æ

 

 

MT2

 

$$RS232_PWRDOWN=<value>

 

Response

 

 

TE2

Å

 

 

MT2

 

$$RS232_PWRDOWN: <value>

 

 

 

 

 

 

<result_code> (OK ERROR)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.3. Low Battery Voltage Notification

MT2 transmits low battery notifications to TE2 and initiates MO SMS alerts by this command where the voltage drops to user determined $$LOWBATT 1 set point or reaches the factory default set points.

NOTE: Whilst the input supply for the is 9–36Vdc, the modem will not power-up at 9 volts. 9.5 volts is required for power-up. MT2 then remains powered-up until the voltage drops to 9 volts.

Extended AT Commands Manual

Page 22 of 70

2009-06-25

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Extended AT Commands Manual RF Exposure Compliance Potentially Unsafe AreasRevision History Contact Information TA BLE of Contents 1.3 2.1 Carrier Command Options Overview General DescriptionTerms SMS PstnRCE TE2Serial Interface AT Inte Rface DescriptionBasic Integration Pin outCommand Format Message Naming ConventionUSB Interface Basic Interface ConfigurationBaud Rate Set-up TE2 MT2TE2 MT2 $$IOFUNCTION? IO FunctionsAT Notification Options TE2 MT2 $$NOTIFCNT?$$NOTIFCNT=value Set command Command$$NOTIFCNT 1 0 Success Failure MT SMS Signal InformationMT Data MT2 Basic Operational State Boot alertInterface Environment Lock order1.4. TE2 active command AT$$TE2ALIVE Power Reset AT$$RESETCurrent time AT$$TIME Power Conservation CommandsSleep mode control AT$$SLEEPENABLE Software version AT$$SWVERExtended AT Commands Manual 2009-06-25 LED control AT$$EXTLED Low Battery Voltage Notification1.3. RS232C Transceiver power-down control AT$$RS232PWRDOWN TE2 MT2 $$EXTLED?Low battery notification AT$$LOWBATT SMS low battery voltage set point AT$$LOWBATTVTGTE2 MT2 $$LOWBATTVTG? Visual/Audible Call Alert Options Receiving notification mode option AT$$RCVMODERinger volume control AT$$RINGLVL Ringer melody selection AT$$RINGIDXAntenna Signal Level report schedule AT$$ANTSET Network Relational SettingsRoaming indicator information AT$$ROAMIND Antenna Signal Level AT$$ANTLVLRssi inquiry AT$$RSSI Modem scheduled Information AT$$PingReading MT2 state AT$$CURRSTATE Location information AT$$LOCATION RF information AT$$RFINFOTE2 MT2 $$LOCATION? LED test AT$$DIAGLED Diagnostic CommandsRing test AT$$DIAGRING Rssi LED response AT$$RSSILEVELPKT Led DescriptionCRT TX/DTRCall released or failed Uses DTR pin Data Call SET UPData Calls MO data call+CSMS action command syntax General Configuration CommandsSelect Message Service +CSMS Preferred Message Storage +CPMSMessage Service Failure Result Code +CMS Error Message Format +CMGFService Centre Address +CSCA Message Configuration CommandsInformative Examples Set Text Mode Parameters +CSMP Show Text Mode Parameters +CSDHMessage Receiving and Reading commands New Message Indications to TE +CNMIAlpha,scts,tooa,fo,pid,dcs,sca,tosca List Messages +CMGL If text mode +CMGF=1, command successful and SMS-SUBMIT If text mode +CMGF=1, command successful and SMS-DELIVERRead Message +CMGR New Message Acknowledgement to ME/TA +CNMA ReportMessage Sending and Writing Commands Send Message +CMGSSuccessful If text mode +CMGF=1 If text mode +CMGF=1 and sendingSend Message from Storage +CMSS If sending failsSend Message Telstra SMS MO AT+MMC Write Message to Memory +CMGWSend Command +CMGC Delete Message +CMGDMore Messages to Send +CMMS AT+CNMI?AT+CMSS=7 SMS Format send and receiveAT$$SMSOPT SMS Send and Receive OptionsSMS Mail Notification Option SMSOPT=AB TE2 MT2 $$SMSOPT?SMS Mail Notification Option SMSOPT=3 SMS Mail Notification Option SMSOPT=1SMS Mail Notification Option SMSOPT=2 Illustrative exampleAuto Delete Messages in ME memory$$AUTODLTSMS Auto delete Messages in ME MemorySMS Notifications SMS Notification $$SMSNOTIFSMS $$LOWBATT 1 set point AT$$LOWBATTVTG SMS Auto Voltage AlertAuto Voltage Alert SMS Site Name AT$$SITENAME TE2 MT2 $$SITENAME?SMS $$LOWBATT 1 set recipient number AT$$AUTOSMS SMS Remote Report RequestsSMS Remote Report Request Site Name AT$$REMOTECTRL Vbatt request Read ALL request10.1.2.4 Rssi request Swver request Location requestDebug Screen request Enter message maxon.reset not case sensitive Remote Reset73 Read command Enter directory number of specific MT2 Value Modem will resetCommand User Remarks Profile NVM vs . US ER PR Ofile StorageUser modified profiles & NVM changes TIA/EIA/IS 707A AT Command SETTE2 MT2 OK Error User Profile store AT&WnSTU Basic AT CommandsBasic AT Parameters IIIBasic S registers Basic action command set Extended AT Commands Manual 2009-06-25 Extended AT configuration command set Extended AT Command SetsBasic result codes +GMM +GCAP+GMI +GMRSpace Default 8Data 1Stop Default+ICF Circuit 106 Clear to Send/Ready for Sending Default Circuit 133 Ready for Receiving Default+IFC 115200bps. Default +IPRTE2 MT2 $$NOTIDS? 13.1.1. RM3 AT$$NOTIDSTE2 MT2 $$NOTIDS +CDS Cellular Extended AT Command SETCellular AT parameter commands +CBC?+CGMM Cellular identification AT command extensions+CGMI +CGMRCellular result codes for Asynchronous data services DM Comman D Diagnostic Mode Debug screen AT$$DBGSCRN Carrier Command OptionsTE2 MT2 $$DBGSCRN
Related manuals
Manual 60 pages 51.94 Kb

MM-6280IND specifications

The Maxon Telecom MM-6280IND is a robust and versatile two-way radio designed to meet the demanding needs of professionals in various fields, including security, construction, and transportation. This model stands out for its combination of advanced features, reliable performance, and user-friendly interface, making it a preferred choice for organizations requiring efficient communication solutions.

One of the key features of the MM-6280IND is its long battery life. Equipped with a high-capacity lithium-ion battery, this radio can provide extended operational time, ensuring that users can stay connected throughout their shifts without frequent recharging interruptions. Additionally, the radio supports multiple battery-saving modes, allowing users to optimize power consumption according to their needs.

The MM-6280IND operates on multiple frequency bands, ensuring compatibility across various communication networks. It supports both analog and digital communication modes, making it adaptable to different environments and user preferences. This dual-mode capability enhances interoperability, allowing seamless communication with other radios, regardless of their technology.

In terms of audio quality, the MM-6280IND features advanced noise-cancellation technology. This ensures clear audio transmission even in noisy environments, such as construction sites or crowded events. Furthermore, the radio is equipped with a built-in speaker and microphone that deliver crisp and loud audio, allowing users to communicate effectively without straining their ears.

Durability is another hallmark of the MM-6280IND. The device is designed to withstand harsh conditions, featuring an IP65 rating for water and dust resistance. This makes it suitable for outdoor use, ensuring that it can function reliably, even in adverse weather conditions. The rugged construction of the radio also protects it from physical impacts, reducing the risk of damage from drops or bumps.

User-friendly functionality is prioritized in the MM-6280IND, with an intuitive keypad and a clear LCD display that make navigation straightforward. It also includes programmable buttons that allow users to customize settings and features according to their specific operational requirements.

Overall, the Maxon Telecom MM-6280IND is a high-performance two-way radio that combines longevity, durability, and adaptability. Its advanced communication technologies and user-focused design make it an excellent tool for professionals seeking efficient and reliable communication solutions in various industries. Whether used for coordinating team efforts or enhancing safety and security, the MM-6280IND is a valuable asset for any organization.
Top Page Image Contents