Maxon Telecom MM-6280IND manual Interface Environment, MT2 Basic Operational State, Boot alert

Page 18

5 . INTERFACE ENVIRONMENT

5.1. MT2 Basic Operational State.

This command set enables the user to set up and/or confirm MT2’s basic operational environment.

5.1.1.1.Boot alert

After power up MT2 notifies TE2 it is active on the network and in idle state by this command.

Set command

 

Command

TE2

Æ

MT2

$$BOOT_ALERT=<value>

 

Response

 

TE2

Å

MT2

$$BOOT_ALERT= <value>

 

 

<result_code> (OK ERROR)

 

 

 

 

 

 

 

Table 5-12 Notification command

 

Command

TE2

Æ

MT2

AT$$BOOT_ALERT?

 

Notify

TE2

Å

MT2

$$TELSTRA 3G

 

VALUE

 

 

 

0 – Disable boot alert

 

 

 

 

1 – Enable Boot alert

 

 

 

 

 

 

 

 

 

 

 

 

 

Note:

If you switch off flow control (AT+IFC=0,0) and set ignore DTR circuit (AT&D0) the boot alert message will not show up on serial port when the modem powers up with firmware R2.1.3.

5.1.1.2.Lock order

If the IMEI or the IMSI stored in MT2 is invalid, MT2 sends this command to TE2.

Table 5-13 Notification command

Notify

TE2

Å

MT2 +CERROR: NO CARRIER

5.1.1.3.SMS TE2 emergency MO registration alert (AT$$EMMOREG)

This command is used for basic monitoring of TE2 condition. MT2 can be set to look for $$TE2ALIVE command from TE2. If MT2 doesn’t receive $$TE2ALIVE command from TE2 within the time frame as set by this $$EMMOREG command, MT2 will assume a problem exists at TE2. MT2 automatically sends an SMS alert message to a user defined mobile number.

$$EMMOREG functionality is disabled after the first alert SMS message to prevent continual SMS transmittal.

NOTE: To re-enable this feature the modem requires the $$EMMOREG Set command to be re-entered.

The applicable TI for this function is; 4098 (text message).

Extended AT Commands Manual

Page 18 of 70

2009-06-25

Image 18
Contents Extended AT Commands Manual RF Exposure Compliance Potentially Unsafe AreasRevision History Contact Information TA BLE of Contents 1.3 2.1 Carrier Command Options Overview General DescriptionTerms SMS PstnRCE TE2Serial Interface AT Inte Rface DescriptionBasic Integration Pin outCommand Format Message Naming ConventionUSB Interface Basic Interface ConfigurationBaud Rate Set-up TE2 MT2TE2 MT2 $$IOFUNCTION? IO FunctionsAT Notification Options TE2 MT2 $$NOTIFCNT?Set command Command $$NOTIFCNT=value$$NOTIFCNT 1 0 Success Failure Signal Information MT SMSMT Data MT2 Basic Operational State Boot alertInterface Environment Lock order1.4. TE2 active command AT$$TE2ALIVE Power Reset AT$$RESETCurrent time AT$$TIME Power Conservation CommandsSleep mode control AT$$SLEEPENABLE Software version AT$$SWVERExtended AT Commands Manual 2009-06-25 LED control AT$$EXTLED Low Battery Voltage Notification1.3. RS232C Transceiver power-down control AT$$RS232PWRDOWN TE2 MT2 $$EXTLED?SMS low battery voltage set point AT$$LOWBATTVTG Low battery notification AT$$LOWBATTTE2 MT2 $$LOWBATTVTG? Visual/Audible Call Alert Options Receiving notification mode option AT$$RCVMODERinger volume control AT$$RINGLVL Ringer melody selection AT$$RINGIDXAntenna Signal Level report schedule AT$$ANTSET Network Relational SettingsRoaming indicator information AT$$ROAMIND Antenna Signal Level AT$$ANTLVLModem scheduled Information AT$$Ping Rssi inquiry AT$$RSSIReading MT2 state AT$$CURRSTATE RF information AT$$RFINFO Location information AT$$LOCATIONTE2 MT2 $$LOCATION? LED test AT$$DIAGLED Diagnostic CommandsRing test AT$$DIAGRING Rssi LED response AT$$RSSILEVELPKT Led DescriptionCRT TX/DTRCall released or failed Uses DTR pin Data Call SET UPData Calls MO data call+CSMS action command syntax General Configuration CommandsSelect Message Service +CSMS Preferred Message Storage +CPMSMessage Service Failure Result Code +CMS Error Message Format +CMGFMessage Configuration Commands Service Centre Address +CSCAInformative Examples Set Text Mode Parameters +CSMP Show Text Mode Parameters +CSDHMessage Receiving and Reading commands New Message Indications to TE +CNMIAlpha,scts,tooa,fo,pid,dcs,sca,tosca List Messages +CMGL If text mode +CMGF=1, command successful and SMS-DELIVER If text mode +CMGF=1, command successful and SMS-SUBMITRead Message +CMGR New Message Acknowledgement to ME/TA +CNMA ReportMessage Sending and Writing Commands Send Message +CMGSSuccessful If text mode +CMGF=1 If text mode +CMGF=1 and sendingSend Message from Storage +CMSS If sending failsSend Message Telstra SMS MO AT+MMC Write Message to Memory +CMGWSend Command +CMGC Delete Message +CMGDMore Messages to Send +CMMS AT+CNMI?AT+CMSS=7 SMS Format send and receiveAT$$SMSOPT SMS Send and Receive OptionsSMS Mail Notification Option SMSOPT=AB TE2 MT2 $$SMSOPT?SMS Mail Notification Option SMSOPT=3 SMS Mail Notification Option SMSOPT=1SMS Mail Notification Option SMSOPT=2 Illustrative exampleAuto Delete Messages in ME memory$$AUTODLTSMS Auto delete Messages in ME MemorySMS Notifications SMS Notification $$SMSNOTIFSMS $$LOWBATT 1 set point AT$$LOWBATTVTG SMS Auto Voltage AlertAuto Voltage Alert SMS Site Name AT$$SITENAME TE2 MT2 $$SITENAME?SMS Remote Report Requests SMS $$LOWBATT 1 set recipient number AT$$AUTOSMSSMS Remote Report Request Site Name AT$$REMOTECTRL Read ALL request Vbatt request10.1.2.4 Rssi request Location request Swver requestDebug Screen request Enter message maxon.reset not case sensitive Remote Reset73 Read command Enter directory number of specific MT2 Value Modem will resetCommand User Remarks Profile NVM vs . US ER PR Ofile StorageUser modified profiles & NVM changes TIA/EIA/IS 707A AT Command SETTE2 MT2 OK Error User Profile store AT&WnSTU Basic AT CommandsBasic AT Parameters IIIBasic S registers Basic action command set Extended AT Commands Manual 2009-06-25 Extended AT Command Sets Extended AT configuration command setBasic result codes +GMM +GCAP+GMI +GMR8Data 1Stop Default Space Default+ICF Circuit 133 Ready for Receiving Default Circuit 106 Clear to Send/Ready for Sending Default+IFC 115200bps. Default +IPR13.1.1. RM3 AT$$NOTIDS TE2 MT2 $$NOTIDS?TE2 MT2 $$NOTIDS +CDS Cellular Extended AT Command SETCellular AT parameter commands +CBC?+CGMM Cellular identification AT command extensions+CGMI +CGMRCellular result codes for Asynchronous data services DM Comman D Diagnostic Mode Carrier Command Options Debug screen AT$$DBGSCRNTE2 MT2 $$DBGSCRN
Related manuals
Manual 60 pages 51.94 Kb

MM-6280IND specifications

The Maxon Telecom MM-6280IND is a robust and versatile two-way radio designed to meet the demanding needs of professionals in various fields, including security, construction, and transportation. This model stands out for its combination of advanced features, reliable performance, and user-friendly interface, making it a preferred choice for organizations requiring efficient communication solutions.

One of the key features of the MM-6280IND is its long battery life. Equipped with a high-capacity lithium-ion battery, this radio can provide extended operational time, ensuring that users can stay connected throughout their shifts without frequent recharging interruptions. Additionally, the radio supports multiple battery-saving modes, allowing users to optimize power consumption according to their needs.

The MM-6280IND operates on multiple frequency bands, ensuring compatibility across various communication networks. It supports both analog and digital communication modes, making it adaptable to different environments and user preferences. This dual-mode capability enhances interoperability, allowing seamless communication with other radios, regardless of their technology.

In terms of audio quality, the MM-6280IND features advanced noise-cancellation technology. This ensures clear audio transmission even in noisy environments, such as construction sites or crowded events. Furthermore, the radio is equipped with a built-in speaker and microphone that deliver crisp and loud audio, allowing users to communicate effectively without straining their ears.

Durability is another hallmark of the MM-6280IND. The device is designed to withstand harsh conditions, featuring an IP65 rating for water and dust resistance. This makes it suitable for outdoor use, ensuring that it can function reliably, even in adverse weather conditions. The rugged construction of the radio also protects it from physical impacts, reducing the risk of damage from drops or bumps.

User-friendly functionality is prioritized in the MM-6280IND, with an intuitive keypad and a clear LCD display that make navigation straightforward. It also includes programmable buttons that allow users to customize settings and features according to their specific operational requirements.

Overall, the Maxon Telecom MM-6280IND is a high-performance two-way radio that combines longevity, durability, and adaptability. Its advanced communication technologies and user-focused design make it an excellent tool for professionals seeking efficient and reliable communication solutions in various industries. Whether used for coordinating team efforts or enhancing safety and security, the MM-6280IND is a valuable asset for any organization.