Sony GDM-17SE2T manual Power Saving Function, Plug and Play, Use of the Tilt-Swivel, Damper Wire

Page 12

Power Saving

Function

This monitor is capable of 3 states of reduced power consumption.

By sensing the absence of one or both sync signals coming from the host computer, it will reduce power consumption as follows.

 

 

Power

Required

POWER

u (power)

Mode

State

resumption

SAVING

consumption

indicator

 

 

 

time

indicator

 

1

Normal

≤ 140 W

off

green on

operation

 

 

 

 

 

 

Standby

 

 

 

 

2

(1st step

≤ 100 W

approx.

orange on

green on

of power

3 sec.

 

 

 

 

 

saving)

 

 

 

 

 

Suspend

 

approx.

 

 

3

(2nd step

≤ 15 W

orange on

green on

of power

3 sec.

 

 

 

 

 

saving)

 

 

 

 

 

Active-off

 

 

 

 

4

(3rd step

≤ 5 W

approx.

orange on

off

of power

10 sec.

 

 

 

 

 

saving)

 

 

 

 

5

Power-off

0 W

off

off

Power Saving Operation

The H-sync is not present.

.

The unit goes into standby state.

The V-sync is not present.

.

The unit goes into suspend state.

Both the H-sync and V-sync are not present.

.

The unit goes into active-off state.

The monitor requires a videocard or screen saver software which switches off one or both sync signals to activate the power saving function.

Caution: The Power Saving function will automatically put the monitor into the Active-off state if the power switch is turned on without any video signal input. Once the horizontal and vertical syncs are sensed, the monitor will automatically return to its Normal operation state.

12

Plug and Play

This monitor complies with the DDCTM1, DDC2B and DDC2AB which are the Display Data Channel (DDC) standards of VESA.

When a DDC1 host system is connected, the monitor synchronizes with the V. CLK in accordance with the VESA standards and outputs the EDID (Extended Display Identification) to the data line.

When a DDC2B or DDC2AB host system is connected, the monitor automatically switches to each communication.

DDCTM is a trademark of Video Electronics Standard Association.

Use of the Tilt-Swivel

With the tilt-swivel, this unit can be adjusted to be viewed at your desired angle within 90° horizontally and 20° vertically.

To turn the unit vertically and horizontally, hold it at its bottom with both hands as illustrated below.

Damper Wire

Using a white background, very thin horizontal stripes on the screen are visible as shown below. These stripes are damper wires. These wires are attached to the aperture grille inside the Trinitron tube and are there to damp vibrations of the aperture grille in order to prevent them from influencing to the picture quality.

Damper wire

GDM-17SE2T:

Approx. 6 cm

GDM-20SE2T:

Approx. 8 cm

GDM-17SE2T:

Approx. 6 cm

GDM-20SE2T:

Approx. 8 cm

Image 12
Contents Multiscan17seII Multiscan20seII Owner’s Record InformationTable of Contents PrecautionsIntroduction Getting Started Using your Monitor Preset and User ModesRecommended horizontal timing conditions Functions of Controls Adjustments Adjusting the Picture CenteringAdjusting the Picture Brightness Adjusting the Picture ContrastAdjustments Adjusting the Picture Size Adjusting the PincushionAdjusting the Picture Rotation For horizontal adjustment Press the ?// buttonsAdjusting the Convergence Setting the Color TemperatureTo obtain the desired color temperature To select 5000K, 6500K or 9300KAdjustments Canceling the Moire Switching the Input ConnectorChecking the Signal Frequency Resetting the Adjustment Data to Factory-preset LevelsIf you want to reset the color temperature Locking the ControlsPower Saving Function Damper WirePower Saving Operation Plug and PlaySpecifications TroubleshootingNo picture Picture is scrambledTroubleshooting Table des matières PrécautionsEntretien Avertissement raccordement électriquePréparation RemarqueUtilisation de votre moniteur Modes par défaut et modes utilisateurFonction des commandes Réglages Réglage de la luminositéRéglage du centrage de l’image Réglage du contrasteRéglages Réglage de la taille de l’image Réglage de la rotation de l’imageRéglage de la distorsion en coussin Pour le réglage de la taille horizontaleRéglage de la convergence Réglage de la température des couleursPour sélectionner 5000K, 6500K ou 9300K Pour obtenir la température de couleur voulueRéglages Suppression du moiré Sélection du connecteur d‘entréeVerrouillage des commandes Vérification de la fréquence du signalRestauration des valeurs par défaut Si vous souhaitez réinitialiser la température des couleursUn moniteur prêt à Economie d’energie l’emploi Utilisation du support pivotantFil d’amortissement Fonction d’économie d’énergieSpécifications Dépannage Pas d’image’image vacille Dépannage Indice IntroducciónPrecauciones Inicio NotaUso del monitor Modos predefinidos y de usuarioFunciones de los controles Ajustes Ajuste del brillo de la imagenAjuste del contraste de la imagen Ajuste de la posición de centrado de la imagenAjustes Ajuste del tamaño de la imagen Ajuste de la distorsión de la imagenAjuste de la rotación de la imagen Para realizar el ajuste vertical Pulse los botones ¨Para seleccionar 5000K, 6500K o 9300K Para obtener la temperatura de color deseadaAjustes Cancelación del efecto muaré Conmutación del conector de entradaBloqueo de los controles Comprobación de la frecuencia de señalRestauración de los valores predefinidos de fábrica Para restaurar la temperatura del colorFunción de ahorro De energíaSoporte basculante giratorio Hilos de amortiguaciónEspecificaciones No aparece ninguna imagenAparecen rayas en la imagen Solución de problemas