Pitney Bowes manual DA300 Basics

Page 32

DA300 Basics • 3

Setting Up A Job (continued)

3. Interface Panel (Not Shown)

Located on the lower part of the rear cover, the panel has the ON/OFF switch, parallel cable connector and power cord receptacle.

4. Wire Frame

Supports the material stack. Adjust the feed angle to accommodate the weight of the material you're running. Adjust its side-to-side position so it's centered under the stack.

5. Material Prop and Lock Knob

The prop adds a gentle slope to the stack to help feeding. Adjust so the top of the prop is even with the top of the stack. Secure the prop with the lock knob.

6. Wireframe Slide

Slides the wireframe side to side. Lock in position with the lock lever (Item7).

7.Wireframe Slide Lock Lever (Not Shown) Locks the wireframe slide in position.

8.Feed Fence

Helps confine the stack. Adjust to the width of your material plus 1/16" clearance.

9. Control Panel

Use the control panel buttons to access printer menus, define print options, run the print job, posi- tion the print carriage and turn the printer on and off line. See Appendix A, Printer Menus, for detailed instructions. Selections can be viewed on the 20- character, dual line LCD display. If you have the DA300 print driver loaded on your computer, you can easily perform these functions from within your application. 10. Stacker Tray

Printed material is deposited in the stacker (catch) tray. The tray holds about 5" of material.

11. Output Area

Where printed material is stacked.

12. Exit Rollers (Not Shown)

Guides the printed material as it exits the printer. Adjust so that each roller overlaps the edge of the material by 1/4". 13. Top Cover

Open to gain access to print cartridge and exit rollers.

DA300 Printer Operator Guide

3-5

Image 32

Contents Page FCC Notice Page Table of Contents Using DA300 With Your Computer Printer MaintenanceTroubleshooting DA300 BasicsIndex Appendix B DA300 SpecificationsAppendix a Control Panel Menus Page Chapter Welcome to the DA300 Using This Guide DA300 Printer OverviewSystem Requirements CPUGetting Help 800Printer Options Ordering Supplies DA300 Printer Overview Setting Up the DA300 Printer Setting Up the DA300 Printer Unpacking the PrinterPackage Contents Setting Up the DA300 Choosing a Location for Your Printer Important Safety Notes Important Safety Notes Assembling the DA300 Setting Up the DA300 Printer Frame under the tabs Feed Fence in Position Pitney Bowes DA300 Operator Guide Stacker Tray Connecting the DA300 to Your Computer Plugging the DA300 Turning the DA300 OnInstalling Removing Ink Jet Cartridge Setting Up the DA300 Printer DA300 Basics Printer Features DA300 BasicsApproved Media Types Material ThicknessMedia Size Setting Up a Job DA300 Basics Set the Separator Gap DA300 Basics Center the Wireform under the Material Wire Frame Lock Knob DA300 Printer Operator Guide Feed Fence Load Material Adjust the Position of the Material Prop Adjust the Media Thickness Lever Adjust the Exit Rollers Line DA300 Basics Using the DA300 With Your Computer Using the DA300 With Your Computer Printer Software Installing the SoftwareDA300 Printer Operator Guide Using the DA300 With Your Computer Using the DA300 With Your Computer Using the DA300 With Your Computer Selecting Printer Properties Using Printer Properties Window General TabUsing the Printer Properties Window Using Properties TabPorts Tab Advanced Tab Using the Printer Properties Window Spooling and Printing Options Security Tab Device Settings Tab Selecting DA300 Printer From a Windows Application Envelope Designer Plus Printer Maintenance Print Quality Problems Printer MaintenancePreventive Maintenance Cleaning Floor Assembly Top Cover Exit Rollers SensorPrinter Maintenance Troubleshooting Troubleshooting Problems and Solutions Feed ProblemsPrint Quality Problems Interface Problems Motor Problems Barcode Problems Other Problems Troubleshooting Troubleshooting Appendix a Using the Control Panel Appendix a Control Panel MenusUsing the Menus Appendix a Control Panel Menus Using the Main Menu Main Menu Menu Options Appendix a Control Panel Menus Address Layout OFF Line Appendix a Control Panel Menus Appendix a Control Panel Menus Font Selection Barcode Appendix a Control Panel Menus Address Recovery Clear Counter Job Settings Appendix a Control Panel Menus Using the Setup Menu Setup Menu Menu Options Appendix a Control Panel Menus Appendix a Control Panel Menus Appendix a Control Panel Menus CR=CRLF=LF Appendix a Control Panel Menus Example Appendix a Control Panel Menus Windows Latin Appendix a Control Panel Menus Appendix a Control Panel Menus Appendix a Control Panel Menus Appendix a Control Panel Menus Appendix B Appendix B Specifications Equipment SpecificationsAppendix B Specifications Appendix B Specifications Dimensional Destination address 3 lines only with no bar code Appendix B Specifications Material Specifications Effective Print AreaAppendix B Specifications Envelope Sizes Index Index DA300 Printer Operator Guide Index Index Index