Pitney Bowes DA300 manual Set the Separator Gap

Page 33

3 • DA300 Basics

Setting Up A Job (continued)

1. Set the Separator Gap

Whenever you switch from one material type to another, you need to set the gap between the separators and the feed roller before printing begins.

To find the correct spacing, see the figure on the next page and follow the instructions below.

Setting the Proper Feed Gap

1.Loosen the lock knobs to unlock all three H-Blocks.

2.Lift the H-Blocks to their highest position and lock in place.

3.Place a sample piece of material between the separa- tor fingers (the lower section of the H-Blocks) and the feed roller.

4.Lower only the “H” Blocks that come in direct contact with the material and let them touch the material.

5.Lock each separator in place. When lowering the H- Blocks, check that the material is between the sepa- rator tabs and the feed roller.

NOTE: If the separator gap is not set properly, the printer will misfeed. If the gap is to big, the printer will feed doubles (two or more pieces at the same time). If the gap is too small, material will jam at the feed roller entrance. If you're running post cards and have feeding problems, set a smaller gap between the H- Block separators and feed rollers.

3-6	DA300 Printer Operator Guide

Image 33

Contents Page FCC Notice Page Table of Contents Printer Maintenance Using DA300 With Your ComputerTroubleshooting DA300 BasicsAppendix B DA300 Specifications Appendix a Control Panel MenusIndex Page Chapter DA300 Printer Overview Welcome to the DA300 Using This GuideCPU System Requirements800 Getting HelpPrinter Options Ordering Supplies DA300 Printer Overview Setting Up the DA300 Printer Unpacking the Printer Setting Up the DA300 PrinterPackage Contents Setting Up the DA300 Choosing a Location for Your Printer Important Safety Notes Important Safety Notes Assembling the DA300 Setting Up the DA300 Printer Frame under the tabs Feed Fence in Position Pitney Bowes DA300 Operator Guide Stacker Tray Connecting the DA300 to Your Computer Turning the DA300 On Plugging the DA300Installing Removing Ink Jet Cartridge Setting Up the DA300 Printer DA300 Basics DA300 Basics Printer FeaturesMaterial Thickness Media SizeApproved Media Types Setting Up a Job DA300 Basics Set the Separator Gap DA300 Basics Center the Wireform under the Material Wire Frame Lock Knob DA300 Printer Operator Guide Feed Fence Load Material Adjust the Position of the Material Prop Adjust the Media Thickness Lever Adjust the Exit Rollers Line DA300 Basics Using the DA300 With Your Computer Printer Software Installing the Software Using the DA300 With Your ComputerDA300 Printer Operator Guide Using the DA300 With Your Computer Using the DA300 With Your Computer Using the DA300 With Your Computer Selecting Printer Properties General Tab Using Printer Properties WindowUsing the Printer Properties Window Properties Tab UsingPorts Tab Advanced Tab Using the Printer Properties Window Spooling and Printing Options Security Tab Device Settings Tab Selecting DA300 Printer From a Windows Application Envelope Designer Plus Printer Maintenance Printer Maintenance Preventive Maintenance CleaningPrint Quality Problems Exit Rollers Sensor Floor Assembly Top CoverPrinter Maintenance Troubleshooting Problems and Solutions Feed Problems TroubleshootingPrint Quality Problems Interface Problems Motor Problems Barcode Problems Other Problems Troubleshooting Troubleshooting Appendix a Appendix a Control Panel Menus Using the Control PanelUsing the Menus Appendix a Control Panel Menus Using the Main Menu Main Menu Menu Options Appendix a Control Panel Menus Address Layout OFF Line Appendix a Control Panel Menus Appendix a Control Panel Menus Font Selection Barcode Appendix a Control Panel Menus Address Recovery Clear Counter Job Settings Appendix a Control Panel Menus Using the Setup Menu Setup Menu Menu Options Appendix a Control Panel Menus Appendix a Control Panel Menus Appendix a Control Panel Menus CR=CRLF=LF Appendix a Control Panel Menus Example Appendix a Control Panel Menus Windows Latin Appendix a Control Panel Menus Appendix a Control Panel Menus Appendix a Control Panel Menus Appendix a Control Panel Menus Appendix B Equipment Specifications Appendix B SpecificationsAppendix B Specifications Appendix B Specifications Dimensional Destination address 3 lines only with no bar code Appendix B Specifications Effective Print Area Material SpecificationsAppendix B Specifications Envelope Sizes Index Index DA300 Printer Operator Guide Index Index Index