Pitney Bowes DA300 manual Appendix B Specifications

Page 112

Appendix B • Specifications

Material Specifications (continued)

Material Notes

Envelopes have a flap along the long edge and are processed by the printer non-flap edge first. Enve- lopes may have either a diagonal or straight edge along the envelope flap.

Booklets are defined as media having physical dimen- sions 6 x 9" or larger. Booklets have an opening along their long edge which is covered by a flap with an adhesive seal.

Catalog envelopes have an opening along their short edge which is closed by a flap with an adhesive seal.

Postcards have no folds or bends. The printable side may have a higher surface roughness than the non- printable side.

Self-mailers may be of "C," "Z," or 1/2-folded con- struction. They may not exceed the maximum allow- able thickness as specified on the previous page and must be tabbed per postal regulations.

A catalog may consist of multiple pages bound by adhesive or tabs on the feed edge or at 90 degrees with respect to the feed edge.

Sheet stock may consist of 16 to 28 lb. bond as well as 60 to 80 lb. coated stock. The size and thickness constraints specified above apply.

Material Size and Thickness

	Width	Height	Thickness

Minimum	5" (127mm)	3" (76mm)	.003" (.0762mm)

Maximum	12.75" (324mm)	13.5" (343mm)	.062" (1.57mm)

Also see the table on the next page.

DA300 Printer Operator Guide

B-9

Image 112

Contents Page FCC Notice Page Table of Contents Using DA300 With Your Computer Printer MaintenanceTroubleshooting DA300 BasicsAppendix a Control Panel Menus Appendix B DA300 SpecificationsIndex Page Chapter Welcome to the DA300 Using This Guide DA300 Printer OverviewSystem Requirements CPUGetting Help 800Printer Options Ordering Supplies DA300 Printer Overview Setting Up the DA300 Printer Setting Up the DA300 Printer Unpacking the PrinterPackage Contents Setting Up the DA300 Choosing a Location for Your Printer Important Safety Notes Important Safety Notes Assembling the DA300 Setting Up the DA300 Printer Frame under the tabs Feed Fence in Position Pitney Bowes DA300 Operator Guide Stacker Tray Connecting the DA300 to Your Computer Plugging the DA300 Turning the DA300 OnInstalling Removing Ink Jet Cartridge Setting Up the DA300 Printer DA300 Basics Printer Features DA300 BasicsMedia Size Material ThicknessApproved Media Types Setting Up a Job DA300 Basics Set the Separator Gap DA300 Basics Center the Wireform under the Material Wire Frame Lock Knob DA300 Printer Operator Guide Feed Fence Load Material Adjust the Position of the Material Prop Adjust the Media Thickness Lever Adjust the Exit Rollers Line DA300 Basics Using the DA300 With Your Computer Using the DA300 With Your Computer Printer Software Installing the SoftwareDA300 Printer Operator Guide Using the DA300 With Your Computer Using the DA300 With Your Computer Using the DA300 With Your Computer Selecting Printer Properties Using Printer Properties Window General TabUsing the Printer Properties Window Using Properties TabPorts Tab Advanced Tab Using the Printer Properties Window Spooling and Printing Options Security Tab Device Settings Tab Selecting DA300 Printer From a Windows Application Envelope Designer Plus Printer Maintenance Preventive Maintenance Cleaning Printer MaintenancePrint Quality Problems Floor Assembly Top Cover Exit Rollers SensorPrinter Maintenance Troubleshooting Troubleshooting Problems and Solutions Feed ProblemsPrint Quality Problems Interface Problems Motor Problems Barcode Problems Other Problems Troubleshooting Troubleshooting Appendix a Using the Control Panel Appendix a Control Panel MenusUsing the Menus Appendix a Control Panel Menus Using the Main Menu Main Menu Menu Options Appendix a Control Panel Menus Address Layout OFF Line Appendix a Control Panel Menus Appendix a Control Panel Menus Font Selection Barcode Appendix a Control Panel Menus Address Recovery Clear Counter Job Settings Appendix a Control Panel Menus Using the Setup Menu Setup Menu Menu Options Appendix a Control Panel Menus Appendix a Control Panel Menus Appendix a Control Panel Menus CR=CRLF=LF Appendix a Control Panel Menus Example Appendix a Control Panel Menus Windows Latin Appendix a Control Panel Menus Appendix a Control Panel Menus Appendix a Control Panel Menus Appendix a Control Panel Menus Appendix B Appendix B Specifications Equipment SpecificationsAppendix B Specifications Appendix B Specifications Dimensional Destination address 3 lines only with no bar code Appendix B Specifications Material Specifications Effective Print AreaAppendix B Specifications Envelope Sizes Index Index DA300 Printer Operator Guide Index Index Index