Pitney Bowes DA300 manual Cr=Crlf=Lf

Page 95

Appendix A • Control Panel Menus

5. Communications	B. Parity
(continued)	Parity determines the integrity of data that is sent. The
	choices are (ODD), (EVEN) and (NONE).
	C. Word Length
	The choices are (7 DATA BITS) and (8 DATA BITS).
	D. Line Termination
	Typical software line termination is CR=CR;LF=LF. If your
	software is not typical, the line termination can be
	modified.
	The menu choices are:
	(CR=CR;LF=LF)
	(CR=CR+LF;LF=LF)
	(CR=CR;LF=CR+LF)
	(CR=CR+LF;LF=CR+LF)

To set the Communications menu option:

1.Press the On Line button until the display reads OFF LINE.

2.Press the Menu button for four seconds to display the Setup Menu.

3.Press the + or – buttons to scroll through the Setup Menu options until the 5. COMMUNICATIONS ap- pears on the LCD panel.

4.Press the Enter button to select the options you want. Continue to press menu, the + and - buttons and enter to scroll to and select the options’ next levels.

5.Press the Menu button to back out of the menu until the printer displays “OFF LINE”.

6.Press the On Line button to enable the printer.

DA300 Printer Operator Guide

A-22

Image 95

Contents Page FCC Notice Page Table of Contents DA300 Basics Using DA300 With Your ComputerPrinter Maintenance TroubleshootingIndex Appendix B DA300 SpecificationsAppendix a Control Panel Menus Page Chapter DA300 Printer Overview Welcome to the DA300 Using This GuideCPU System Requirements800 Getting HelpPrinter Options Ordering Supplies DA300 Printer Overview Setting Up the DA300 Printer Unpacking the Printer Setting Up the DA300 PrinterPackage Contents Setting Up the DA300 Choosing a Location for Your Printer Important Safety Notes Important Safety Notes Assembling the DA300 Setting Up the DA300 Printer Frame under the tabs Feed Fence in Position Pitney Bowes DA300 Operator Guide Stacker Tray Connecting the DA300 to Your Computer Turning the DA300 On Plugging the DA300Installing Removing Ink Jet Cartridge Setting Up the DA300 Printer DA300 Basics DA300 Basics Printer FeaturesApproved Media Types Material ThicknessMedia Size Setting Up a Job DA300 Basics Set the Separator Gap DA300 Basics Center the Wireform under the Material Wire Frame Lock Knob DA300 Printer Operator Guide Feed Fence Load Material Adjust the Position of the Material Prop Adjust the Media Thickness Lever Adjust the Exit Rollers Line DA300 Basics Using the DA300 With Your Computer Printer Software Installing the Software Using the DA300 With Your ComputerDA300 Printer Operator Guide Using the DA300 With Your Computer Using the DA300 With Your Computer Using the DA300 With Your Computer Selecting Printer Properties General Tab Using Printer Properties WindowUsing the Printer Properties Window Properties Tab UsingPorts Tab Advanced Tab Using the Printer Properties Window Spooling and Printing Options Security Tab Device Settings Tab Selecting DA300 Printer From a Windows Application Envelope Designer Plus Printer Maintenance Print Quality Problems Printer MaintenancePreventive Maintenance Cleaning Exit Rollers Sensor Floor Assembly Top CoverPrinter Maintenance Troubleshooting Problems and Solutions Feed Problems TroubleshootingPrint Quality Problems Interface Problems Motor Problems Barcode Problems Other Problems Troubleshooting Troubleshooting Appendix a Appendix a Control Panel Menus Using the Control PanelUsing the Menus Appendix a Control Panel Menus Using the Main Menu Main Menu Menu Options Appendix a Control Panel Menus Address Layout OFF Line Appendix a Control Panel Menus Appendix a Control Panel Menus Font Selection Barcode Appendix a Control Panel Menus Address Recovery Clear Counter Job Settings Appendix a Control Panel Menus Using the Setup Menu Setup Menu Menu Options Appendix a Control Panel Menus Appendix a Control Panel Menus Appendix a Control Panel Menus CR=CRLF=LF Appendix a Control Panel Menus Example Appendix a Control Panel Menus Windows Latin Appendix a Control Panel Menus Appendix a Control Panel Menus Appendix a Control Panel Menus Appendix a Control Panel Menus Appendix B Equipment Specifications Appendix B SpecificationsAppendix B Specifications Appendix B Specifications Dimensional Destination address 3 lines only with no bar code Appendix B Specifications Effective Print Area Material SpecificationsAppendix B Specifications Envelope Sizes Index Index DA300 Printer Operator Guide Index Index Index