Diamond Power Products MM-48-AT user manual Specifications, Autocalibration, General

Page 44

17. SPECIFICATIONS

Analog Inputs

No. of inputs

16 single-ended

 

A/D resolution

16 bits (1/65,536 of full scale)

Input ranges

Bipolar model:

±10V, ±5V

 

Unipolar model:

0-5V

Input bias current

50nA max

 

Maximum input voltage

±10V for linear operation

Overvoltage protection

±35V on any analog input without damage

Nonlinearity

±3LSB, no missing codes

Max conversion rate

200,000 samples per second aggregate for all channels in use

Conversion trigger

software trigger, internal pacer clock, or external TTL signal

Autocalibration

Circuits calibrated

A/D and D/A

A/D error

±1LSB (typical), ±2LSB (max) after autocalibration

D/A error

±1LSB (typical), ±2LSB (max) after autocalibration

Analog Outputs

No. of outputs

8

 

D/A resolution

12 bits (1/4096 of full scale)

Output range

0 – 4.095V

Output current

Source: 4mA max; Sink: 0.5-4mA depending on output voltage

Settling time

7S max to ±1/2 LSB

Integral nonlinearity

±6

LSB max, D/A code >= 20

Nonlinearity

±1

LSB, monotonic

Digital I/O

No. of lines

4, 3.3V and 5V logic compatible

Input voltage

Logic 0: 0.0V min, 0.8V max; Logic 1: 2.0V min, 5.0V max

Input current

±1A max

Output voltage

Logic 0:

0.0V min, 0.50V max; Logic 1: 2.4V min, 3.3V max

Output current

Logic 0:

8mA max; Logic 1: -6mA max

Optocoupler Inputs

No. of lines

4

Input voltage

3-28V DC or AC to turn on

Relay Outputs

No. of relays

8, SPDT (form C); type Omron G6K or equivalent

Capacity

1A / 30VDC (max 60VDC at 0.5A), 0.3A / 125VAC

Counter/Timers

A/D pacer clock

24-bit down counter

Pacer clock source

10MHz or 1MHz on-board clock source

General purpose

16-bit down counter

General

Power supply

+5VDC ±10%

 

Current consumption

150mA + 30mA per activated relay typical

 

±15V output current

±10mA max with DACs unloaded; not short-circuit protected

+5V output current

Limited by PC/104 power supply; not short-circuit protected

Operating temperature

-40 to +85oC

 

Operating humidity

5% to 95% noncondensing

 

 

Diamond-MM-48-AT User Manual V1.01

Page 44

Image 44
Contents DIAMOND-MM-48-AT Table of Contents Description DIAMOND-MM-48-AT Board Drawing J3 Analog and Digital I/O Signal Name DefinitionO Header Pinout and PIN Description Optoisolated input contacts Signal Name Definition Relay output contactsJ4 Relays and Optocouplers Board Configuration Base AddressBase Address Jumper Position Hex Decimal Interrupt Level SelectionAnalog Input Range Optocoupler PolarityReserved LSB MSB OverviewBase + Write Function Read Function Register Map Bit Assignments Write operationsDA7 DA6 DA5 DA4 DA3 DA2 DA1 DA0 Read operationsRegister Definitions Base + WriteDefinitions Base + ReadHIGH3 HIGH2 HIGH1 HIGH0 LOW3 LOW2 LOW1 LOW0 AD9 AD8Base + Read/Write A/D Channel Register Base + Read/Write Digital I/O Configuration Register Base + Read/Write Relay Control PortRELAY7 RELAY6 RELAY5 RELAY4 RELAY3 RELAY2 RELAY1 RELAY0 DIR3 DIR2 DIR1 DIR0DIO3 DIO2 DIO1 DIO0 Base + Read Digital I/O Data and Edge StatusDEDGE3 DEDGE2 DEDGE1 DEDGE0 DIO3 DIO2 DIO1 DIO0 OEN3 OEN2 OEN1 OEN0 POL3 POL2 POL1 POL0OEDGE3 OEDGE2 OEDGE1 OEDGE0 OPTO3 OPTO2 OPTO1 OPTO0 Base + Write Channel and Control RegisterDaupdt DACH2 DACH1 DACH0 Base + Write Command Register Dapre Daprld Reset Fiforst AdstartBase + Read Status Register POL ADCH3 ADCH2 ADCH1 ADCH0Base + Write Configuration Register CKSEL1 CKFRQ1 CKFRQ0 Scnint Clken ClkselBase + Read Configuration & Status Register Adbusy Dabusy CKSEL1 CKFRQ1 CKFRQ0 Scnint Clken ClkselBase + Write Fifo Control Register Fifoth Fifoen ScanenBase + Read Fifo Status Register OVF Fifoth Fifoen ScanenBase + Write Interrupt Control Register Clrt Clrd Clro Clra Tinte Dinte Ointe AinteBase + Read Interrupt Status Register Tint Dint Oint Aint Tinte Dinte Ointe AinteBase + Read/Write Counter/Timer D23 Base + Read/Write Counter/Timer D7Base + Read/Write Counter/Timer D15 Ctrno Base + Write Counter/Timer Control RegisterCtrno Latch Gtdis Gten Ctdis Cten Load CLR Base + Read/Write Eeprom / TrimDAC Data Register Base + Read/Write Eeprom / TrimDAC Address RegisterBase + Write Eeprom Access Key Register Base + Write Calibration Control RegisterBase + Read Calibration Status Register Base + Read Fpga Revision CodeAnalog Input Ranges and Resolution ResolutionInput Ranges Single Ended and Differential InputsPerforming AN A/D Conversion Trigger an A/D conversion on the current channel LSB = readbase MSB = readbase+1 Data = MSB * 256 + LSBInput voltage = A/D value / 32768 * Full-scale voltage D SCAN, FIFO, and Interrupt Operation TriggerClken Clksel Conversion or ScanFifo Operation Interrupt OperationFifoen Fifoth Scanen Fifoen =Ainte Fifoen Scanen Guidelines for Selecting Fifo Use Fifoen and FifothOperation Table Analog Output Overview Generating AN Analog Output Autocalibration Operation Reference Voltages12.2 A/D calibration 12.3 D/A CalibrationDigital I/O Operation Procedure for enabling interrupts on selected edges Optocoupler OperationEdge detection assumes OENn = 1 to enable edge detection Polarity and logic readbackRelay Operation Counter 1 Counting/Totalizing Functions COUNTER/TIMER OperationCounter 0 A/D Sample Control Command Sequences CounterCounter Outpbase+15,0x01 Outpbase+15,0x81 General SpecificationsAutocalibration