Diamond Power Products MM-48-AT Base + Read/Write Relay Control Port, DIR3 DIR2 DIR1 DIR0

Page 13

Base + 3

Read/Write

Relay Control Port

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bit No.

7

 

6

5

4

3

2

1

0

 

 

 

 

 

 

 

 

 

Name

RELAY7

RELAY6

RELAY5

RELAY4

RELAY3

RELAY2

RELAY1

RELAY0

 

 

 

 

 

 

 

 

 

 

These bits control the 8 relays. 0 = off (C connected to NC), 1 = on (C connected to NO). The written value may be read back with true logic. The value on the corresponding output pin is the inverse of the value in this register.

On power-up or reset, the output register is cleared to all zeroes and all relays reset to their off condition (C connected to NC) by resetting all RELAY pins to 1. Relays are in the off condition when power is off and remain in that condition when power is applied until a 1 is written to their corresponding control register bit.

Base + 4

Read/Write

 

Digital I/O Configuration Register

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bit No.

7

 

6

 

5

4

3

2

1

0

 

 

 

 

 

 

 

 

 

 

 

Name

 

 

 

 

 

 

DIR3

DIR2

DIR1

DIR0

 

 

 

 

 

 

 

 

 

 

 

Definitions:

DIR3-0 Digital I/O direction settings for each bit: 1 = output, 0 = input

All digital I/O lines are in input mode on power-up.

Diamond-MM-48-AT User Manual V1.01

Page 13

Image 13
Contents DIAMOND-MM-48-AT Table of Contents Description DIAMOND-MM-48-AT Board Drawing O Header Pinout and PIN Description Signal Name DefinitionJ3 Analog and Digital I/O J4 Relays and Optocouplers Signal Name Definition Relay output contactsOptoisolated input contacts Base Address Board ConfigurationBase Address Jumper Position Hex Decimal Interrupt Level SelectionReserved Optocoupler PolarityAnalog Input Range Base + Write Function Read Function OverviewLSB MSB Write operations Register Map Bit AssignmentsDA7 DA6 DA5 DA4 DA3 DA2 DA1 DA0 Read operationsBase + Write Register DefinitionsDefinitions Base + ReadBase + Read/Write A/D Channel Register AD9 AD8HIGH3 HIGH2 HIGH1 HIGH0 LOW3 LOW2 LOW1 LOW0 Base + Read/Write Relay Control Port Base + Read/Write Digital I/O Configuration RegisterRELAY7 RELAY6 RELAY5 RELAY4 RELAY3 RELAY2 RELAY1 RELAY0 DIR3 DIR2 DIR1 DIR0Base + Read Digital I/O Data and Edge Status DIO3 DIO2 DIO1 DIO0DEDGE3 DEDGE2 DEDGE1 DEDGE0 DIO3 DIO2 DIO1 DIO0 OEN3 OEN2 OEN1 OEN0 POL3 POL2 POL1 POL0Daupdt DACH2 DACH1 DACH0 Base + Write Channel and Control RegisterOEDGE3 OEDGE2 OEDGE1 OEDGE0 OPTO3 OPTO2 OPTO1 OPTO0 Dapre Daprld Reset Fiforst Adstart Base + Write Command RegisterPOL ADCH3 ADCH2 ADCH1 ADCH0 Base + Read Status RegisterCKSEL1 CKFRQ1 CKFRQ0 Scnint Clken Clksel Base + Write Configuration RegisterAdbusy Dabusy CKSEL1 CKFRQ1 CKFRQ0 Scnint Clken Clksel Base + Read Configuration & Status RegisterFifoth Fifoen Scanen Base + Write Fifo Control RegisterBase + Read Fifo Status Register OVF Fifoth Fifoen ScanenClrt Clrd Clro Clra Tinte Dinte Ointe Ainte Base + Write Interrupt Control RegisterTint Dint Oint Aint Tinte Dinte Ointe Ainte Base + Read Interrupt Status RegisterBase + Read/Write Counter/Timer D15 Base + Read/Write Counter/Timer D7Base + Read/Write Counter/Timer D23 Ctrno Latch Gtdis Gten Ctdis Cten Load CLR Base + Write Counter/Timer Control RegisterCtrno Base + Read/Write Eeprom / TrimDAC Address Register Base + Read/Write Eeprom / TrimDAC Data RegisterBase + Write Calibration Control Register Base + Write Eeprom Access Key RegisterBase + Read Calibration Status Register Base + Read Fpga Revision CodeResolution Analog Input Ranges and ResolutionInput Ranges Single Ended and Differential InputsPerforming AN A/D Conversion LSB = readbase MSB = readbase+1 Data = MSB * 256 + LSB Trigger an A/D conversion on the current channelInput voltage = A/D value / 32768 * Full-scale voltage Trigger D SCAN, FIFO, and Interrupt OperationClken Clksel Conversion or ScanInterrupt Operation Fifo OperationFifoen Fifoth Scanen Fifoen =Operation Table Guidelines for Selecting Fifo Use Fifoen and FifothAinte Fifoen Scanen Analog Output Overview Generating AN Analog Output Reference Voltages Autocalibration Operation12.2 A/D calibration 12.3 D/A CalibrationDigital I/O Operation Optocoupler Operation Procedure for enabling interrupts on selected edgesPolarity and logic readback Edge detection assumes OENn = 1 to enable edge detectionRelay Operation Counter 0 A/D Sample Control COUNTER/TIMER OperationCounter 1 Counting/Totalizing Functions Counter Command SequencesCounter Outpbase+15,0x01 Outpbase+15,0x81 Autocalibration SpecificationsGeneral