Datamax M-4206 manual Agency Compliance and Approvals

Page 3

Agency Compliance and Approvals:

UL60950 Information Technology Equipment

C22.2 No. 950-M93

CUS

Listed

EN60950

For 230 Volt Operation (Europe): Use a cord set, marked "HAR," consisting of a min H05VV-F cord which has a minimum 0.75 square mm diameter conductors, provided with an IEC 320 receptacle and a male plug for the country of installation rated 6A, 250V

Für 230 Volt (Europa): Benützen Sie ein Kabel, das mit "HAR" markiert ist, bestehend mindestens aus einem H05VV-F Kabel, das mindestens 0,75 Quadratmillimeter Drahtdurchmesser hat; sowie eine IEC320 Steckdose und einen für das Land geeigneten Stecker, 6A, 250 Volt.

As an Energy Star Partner, the manufacturer has determined that this product meets the Energy Star guidelines for energy efficiency.

The manufacturer declares under sole responsibility that this product conforms to the following standards or other normative documents:

EMC:	EN 55022	(1993) Class B
	EN 50024	(1998)

Safety: This product complies with the requirements of EN 60950 /A11:1997

Gost-R

FCC: This device complies with FCC CFR 47 Part 15 Class A.

;Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions in this manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Image 3

Contents Operator’s Manual Copyright Information Agency Compliance and Approvals Important Safety Instructions Printer Overview Troubleshooting Introduction About this Printer Standard FeaturesThermal Transfer Optional Features4206 Removing the Packaging Before Using the PrinterAdditional Requirements Inspecting the PrinterPower Connection Connecting the PrinterUSB Connection Interface ConnectionLoading Media 4206 4206 Sensor Eye Mark Position Media Sensor AdjustmentLoading Ribbon 4206 Ribbon Routing Coated Side In & Coated Side Out Lights Normal ModeButtons Normal Mode Button FunctionsExpress Setup Mode Button Functions To change Printer Setup Printer Setup Mode Button FunctionsMenu Item Values Numbers Items Printer Setup Menu ListMedia Type Sensor Type Menu Items and ValuesControl Codes Form Length Align Length Stop Location Step by Step Modification of the Printer Setup New 19200 Baud Rate Label Alignment = YES Label AlignmentLabel Alignment = no Label Alignment = AutoProblem Possible Cause Solution Label Alignment TroubleshootingIncorrect. Pressing Not correct. The default To perform Calibration Calibration Mode Button FunctionsAuto Media Sensor Calibration Manual Media Sensor Calibration Internal Labels Database Configuration and Dot Check LabelsGood Dot Check Label To print the Test Label Test LabelTo print the Hex Dump Label Hex Dump LabelArea Method Interval Cleaning the Printhead Media Width Adjustment Printhead Burn Line Adjustment Printhead Pressure Adjustment Removal Printhead ReplacementResetting to the Factory Defaults Darkness AdjustmentDownloading Firmware and Fonts Problem Situation Troubleshooting TipsUnacceptable print quality Skips every other label Label advances 16 inches before a fault indication Printing MechanicalEmbedded Bar Codes Media/RibbonCommunications FontsSide View Top View Approved Media4206 Ascii Control Code Chart XON Font Valid Ascii Characters decimal Use with Record Embedded Fonts and BarcodesAlphanumeric, upper and lower Font 6 62-character alphanumeric, uppercase 4206 Bar Code Type Length Check Valid Ascii Characters Sum BarcodesFIM Barcode a Code 3 Barcode I Codabar Barcode T Telepen Barcode v FIM Bar Code W1c DataMatrix Thermal Printhead PrinterWarranty Service Procedures General Warranty ProvisionsLimitation of Liability Glossary 4206 4206 4206