Datamax M-4206 manual New 19200 Baud Rate

Page 31

6.To confirm that your changes have been made press the FEED + CANCEL buttons simultaneously, this will print the Database Configuration Label. The label should show the new Baud Rate value of 19200.

FRI JANUARY 10, 2003 19:29 010 VER: M4206 - 05.03 01/07/03 BOOT 83-2383-05C

CODE 83-2385-05C

FPGA 83-2384-05A

FONT 83-2386-05C

256K FLASH MODULE B

SYSTEM FLASH SIZE_____2 MBYTES

SYSTEM RAM CHECKS____ GOOD

SYSTEM RAM SIZE___ 4096 KBYTES SYSTEM RAM AVAIL__ 3180 KBYTES

AUTO DETECTION CUTTER____________NOT DETECTED

PRESENT SENSOR____NOT DETECTED

CURRENT STOP LOC__TEAR

EXPRESS SETUP

MEDIA SENSOR______EDGE

PRINT METHOD______TRANSFER

OPTION CONTROL____AUTO

INPUT VALUES

PAPER_____________ 207

DARKNESS__________ 119

TRAN______________ 157

REFL______________ 0

RIBN______________ 237

TEMP______________ 64

VOLT______________ 218

PRESENT SENSOR____ 0

CONFIGURATION
SERIAL PORT SELECTED
19.2; 8BITS
EDGE
MEDIA TYPE________		TRANSFER
CONT FORM LENGTH__			0
PRESENT ADJUST____		128
SOP ADJUST________		128
TOF LOW___________			0	0
TOF DELTA_________		10		10
TOF GAIN__________			7	5
OOS MAXVOLT_______			3	2
LABEL ALIGNMENT___		AUTO
ALIGN LENGTH______		611
STOP LOCATION_____		AUTO
INPUT MODE________		DPL
DPL EMULATION_____		STANDARD
HEAT______________		10
COUNTER INFORMATION
ABSOLUTE VALUES		1-	7-2003
LENGTH____		773	INCHES
TIME______		20	HOURS
RESETTABLE VALUES		1-	7-2003
LENGTH____		576	INCHES
TIME______		10	HOURS
MEMORY CONFIGURATION
INTERNAL MODULE A______				128
SCALABLE FONTS_________				64
LABEL SIZE	0426:11255 IN

The new 19200 Baud Rate

M-4206

25

Image 31

Contents Operator’s Manual Copyright Information Agency Compliance and Approvals Important Safety Instructions Printer Overview Troubleshooting Introduction About this Printer Standard FeaturesThermal Transfer Optional Features4206 Removing the Packaging Before Using the PrinterAdditional Requirements Inspecting the PrinterPower Connection Connecting the PrinterUSB Connection Interface ConnectionLoading Media 4206 4206 Sensor Eye Mark Position Media Sensor AdjustmentLoading Ribbon 4206 Ribbon Routing Coated Side In & Coated Side Out Lights Normal ModeButtons Normal Mode Button FunctionsExpress Setup Mode Button Functions To change Printer Setup Printer Setup Mode Button FunctionsMenu Item Values Numbers Items Printer Setup Menu ListMedia Type Sensor Type Menu Items and ValuesControl Codes Form Length Align Length Stop Location Step by Step Modification of the Printer Setup New 19200 Baud Rate Label Alignment = YES Label AlignmentLabel Alignment = no Label Alignment = AutoProblem Possible Cause Solution Label Alignment TroubleshootingIncorrect. Pressing Not correct. The default To perform Calibration Calibration Mode Button FunctionsAuto Media Sensor Calibration Manual Media Sensor Calibration Internal Labels Database Configuration and Dot Check LabelsGood Dot Check Label To print the Test Label Test LabelTo print the Hex Dump Label Hex Dump LabelArea Method Interval Cleaning the Printhead Media Width Adjustment Printhead Burn Line Adjustment Printhead Pressure Adjustment Removal Printhead ReplacementResetting to the Factory Defaults Darkness AdjustmentDownloading Firmware and Fonts Problem Situation Troubleshooting TipsUnacceptable print quality Skips every other label Label advances 16 inches before a fault indication Printing MechanicalEmbedded Bar Codes Media/RibbonCommunications FontsSide View Top View Approved Media4206 Ascii Control Code Chart XON Font Valid Ascii Characters decimal Use with Record Embedded Fonts and BarcodesAlphanumeric, upper and lower Font 6 62-character alphanumeric, uppercase 4206 Bar Code Type Length Check Valid Ascii Characters Sum BarcodesFIM Barcode a Code 3 Barcode I Codabar Barcode T Telepen Barcode v FIM Bar Code W1c DataMatrix Thermal Printhead PrinterGeneral Warranty Provisions Warranty Service ProceduresLimitation of Liability Glossary 4206 4206 4206