Datamax M-4206 manual Internal Labels, Database Configuration and Dot Check Labels

Page 39

4.8Internal Labels

The following section details the printer’s internally generated configuration and test labels.

4.8.1 Database Configuration and Dot Check Labels

The Database Configuration Label provides valuable printer information including the firmware version, memory allocations, enabled options, and label-counter data.

To print the Database Configuration and Dot Check Labels:

With the printer on, loaded with media (at least 4 inches wide) and ribbon (if printing with thermal transfer media), press the FEED + CANCEL buttons simultaneously.

The first label printed will be the Database Configuration Label.

FRI JANUARY 10, 2003 19:29 010		CONFIGURATION
VER: M4206 - 05.03	01/07/03	SERIAL PORT SELECTED
BOOT 83-2383-05C		19.2; 8BITS
CODE 83-2385-05C		EDGE
FPGA 83-2384-05A		MEDIA TYPE________		TRANSFER
FONT 83-2386-05C		CONT FORM LENGTH__		0
256K FLASH MODULE	B	PRESENT ADJUST____		128
SYSTEM FLASH SIZE_____2 MBYTES		SOP ADJUST________		128
SYSTEM RAM CHECKS____ GOOD		TOF LOW___________		0	0
SYSTEM RAM SIZE___	4096 KBYTES	TOF DELTA_________		10	10
SYSTEM RAM AVAIL__	3180 KBYTES	TOF GAIN__________		7	5
		OOS MAXVOLT_______		3	2
AUTO DETECTION		LABEL ALIGNMENT___		AUTO
CUTTER____________NOT DETECTED		ALIGN LENGTH______		611
PRESENT SENSOR____NOT DETECTED		STOP LOCATION_____		AUTO
CURRENT STOP LOC__TEAR		INPUT MODE________		DPL
		DPL EMULATION_____		STANDARD
EXPRESS SETUP		HEAT______________		10
MEDIA SENSOR______EDGE
PRINT METHOD______TRANSFER
OPTION CONTROL____AUTO		COUNTER INFORMATION
		ABSOLUTE VALUES		1- 7-2003
		LENGTH____		773 INCHES
INPUT VALUES		TIME______		20 HOURS
PAPER_____________	207	RESETTABLE VALUES		1- 7-2003
DARKNESS__________	119	LENGTH____		576 INCHES
TRAN______________	157	TIME______		10 HOURS
REFL______________	0
RIBN______________	237	MEMORY CONFIGURATION
TEMP______________	64	INTERNAL MODULE A______			128
VOLT______________	218	SCALABLE FONTS_________			64
PRESENT SENSOR____	0	LABEL SIZE	0426:11255 IN

M-4206

33

Image 39

Contents Operator’s Manual Copyright Information Agency Compliance and Approvals Important Safety Instructions Printer Overview Troubleshooting Introduction About this Printer Standard FeaturesThermal Transfer Optional Features4206 Removing the Packaging Before Using the PrinterAdditional Requirements Inspecting the PrinterPower Connection Connecting the PrinterUSB Connection Interface ConnectionLoading Media 4206 4206 Sensor Eye Mark Position Media Sensor AdjustmentLoading Ribbon 4206 Ribbon Routing Coated Side In & Coated Side Out Lights Normal ModeButtons Normal Mode Button FunctionsExpress Setup Mode Button Functions To change Printer Setup Printer Setup Mode Button FunctionsMenu Item Values Numbers Items Printer Setup Menu ListMedia Type Sensor Type Menu Items and ValuesControl Codes Form Length Align Length Stop Location Step by Step Modification of the Printer Setup New 19200 Baud Rate Label Alignment = YES Label AlignmentLabel Alignment = no Label Alignment = AutoProblem Possible Cause Solution Label Alignment TroubleshootingIncorrect. Pressing Not correct. The default To perform Calibration Calibration Mode Button FunctionsAuto Media Sensor Calibration Manual Media Sensor Calibration Internal Labels Database Configuration and Dot Check LabelsGood Dot Check Label To print the Test Label Test LabelTo print the Hex Dump Label Hex Dump LabelArea Method Interval Cleaning the Printhead Media Width Adjustment Printhead Burn Line Adjustment Printhead Pressure Adjustment Removal Printhead ReplacementResetting to the Factory Defaults Darkness AdjustmentDownloading Firmware and Fonts Problem Situation Troubleshooting TipsUnacceptable print quality Skips every other label Label advances 16 inches before a fault indication Printing MechanicalEmbedded Bar Codes Media/RibbonCommunications FontsSide View Top View Approved Media4206 Ascii Control Code Chart XON Font Valid Ascii Characters decimal Use with Record Embedded Fonts and BarcodesAlphanumeric, upper and lower Font 6 62-character alphanumeric, uppercase 4206 Bar Code Type Length Check Valid Ascii Characters Sum BarcodesFIM Barcode a Code 3 Barcode I Codabar Barcode T Telepen Barcode v FIM Bar Code W1c DataMatrix Thermal Printhead PrinterWarranty Service Procedures General Warranty ProvisionsLimitation of Liability Glossary 4206 4206 4206