Citizen Systems CBM920II user manual Control Code Details, SW1 Switch No.1, SW2 Switch No.2

Page 40

8.2 Control Code Details

(1) Command for Line Feed After Printing (CR/LF)

By entering CR (0DH)/LF (0AH) codes, data in the print buffer is printed followed by a line feed. Without data in the print buffer, only a line feed is performed. This command is ignored just after buffer full in case of 920 emulation.

CR and LF are valid in the following conditions.

CBM-920 Emulation

 

SW1 Switch No.1

 

 

OFF

ON

 

Serial

LF only

CR and LF

 

Parallel

LF only

CR and LF

 

 

iDP3110 Emulation

 

SW2 Switch No.2

 

 

OFF

ON

 

Serial

CR only

LF only

 

Parallel

LF only

CR only

(2) Specify/Clear double-width character (SI, SO, US, RS, and DC4) command

SI/SO codes function in the same manner as US/RS as long as 8-bit data are assigned (serial communication data bit length), which, however, are divided, under 7-bit assignment, into SI (20H~7FH characters) print assignment and SO (A0H~FFH characters) print assignment functions.

1.Standard letter assignment (SO/RS) command:

With SI (0FH)/US (1FH) codes input, lateral enlargement is cancelled and the data following are printed in standard letters. This command can cancel only lateral enlargement, which dose not apply to ⋅4 enlargement.

2.Laterally enlarged letter assignment (SO/RS) command:

With SO (0EH)/RS (1EH) codes input in any columns, the data following are printed in prints enlarged double in width.

Although standard and enlarged letters can be mixed within one line, automatic (buffer-full) printing takes place when the number of columns reaches 24 (or 40) counted in standard letters. With 920 emulation, laterally enlarged letter assignment is cleared by printing after line feed, followed by SI, US, and DC1. With 3110 emulation, it is cleared by printing after line feed by LF and CR, followed by SI, US, and DC4.

[Example of receive data

[Results of Printing]

(For 24-column model)]

 

SO

1234567890

CR

SO

123

SI

ABCD

 

CR

 

 

 

 

 

 

 

 

 

 

 

SO

123

SI

ABCD

 

SO

12

CR

 

 

 

 

 

 

SO

SO

12345678901B

 

— 37 —

Page 39 Page 41
Image 40
Page 39 Page 41
Contents DOT Matrix Printer Weee Mark Declaration of Conformity General Precautions Ordinarymaintenance Page Precautions for Installation Precautions for Handling Table of Contents External Dimensions Accessories FeaturesIntroduction Type Classifications Power supplyType Specifications CBM-920II-24 CBM-920II-40External Appearance and Part Descriptions External AppearancePart Descriptions Operations Rack MountingI/F Cable Connection Panel Opening/Closing Opening/Closing of Front PanelSetting Ribbon Cassette Paper FeedingSetting Paper Page Auto Loading Function Self-printing Function, Hexadecimal Printing Function Memory Switch Setting Japan 920JPN International 920IntlPage Contents of Memory Switch Setting CBM-920II 10 PNE, PE, Other errors Return Paper lamp Power lamp Signal line Clearing Lamp Status, I/F signal status, error, etcState Special Functions Pin Signal Name Connector Pin AssignmentParallel Interface Description of Input/Output Signals Electrical Characteristics Host Side Printer SideSerial Interface TTL , CmosDescription of Input/Output Signal Dtrdata Terminal ReadyError Detection Receiving Control and BufferingDIP Switch SW1 Setting DIP Switch PositionSwitch No Function Factory SettingSwitch No Baud Rate Parity Factory Setting Bps Serial Interface TypePrint Control Function Symbol Code Function Emulation Hexadecimal CBM920 IDP3110List of Control Codes SW2 Switch No.2 SW1 Switch No.1Control Code Details ABC Country Character Code TableESC Page FF FF FF FF FF FF For 40-column model 3 4 5 6 41H 22H 55H 08H 41H 00H 41H Model CBM-920 emulation For manual setting, refer to 4.9 Setting Memory Switch Setting range of parameters n1 and n2 is as shown below Function Content of SettingCharacter Code Table Code page tablePage Page Page International Character Code Table External Dimensions
Top Page Image Contents