Citizen Systems CBM920II Serial Interface Type, Switch No Baud Rate Parity Factory Setting Bps

Page 38

7.3 Serial Interface Type

	Switch No.	Function	OFF	ON	Factory Setting
	1	Character direction	Normal	Inverted	OFF
	2 (920)*	CR command	Ignore CR	CR + LF	OFF
	2 (3110)	CR command	—	—	OFF
	3	Reset in	Disable	Enable	ON
	4	Memory switch	Disable Setting	Enable Setting	OFF
	5				OFF
	5	Transmission rate			OFF
	6	Transmission rate	The following reference		OFF
	6	and parity	The following reference		OFF
	7	and parity			OFF
	7				OFF
	8				OFF

* Difference may occur in accordance with the emulation set by the memory switch.

Set DIP switch No. 4 to ON. Then turn the printer power on while pressing and holding the FEED switch. The printer enters the manual memory switch setting mode. After manual setting mode, be sure to set this switch to Off.

Baud rate and parity selection

	Switch No.			Baud Rate	Parity	Factory Setting
8	7	6	5	(bps)
OFF	OFF	OFF	OFF	4800	None	O
OFF	OFF	OFF	ON	1200	None	—
OFF	OFF	ON	OFF	2400	None	—
OFF	OFF	ON	ON	4800	None	—
OFF	ON	OFF	OFF	9600	None	—
OFF	ON	OFF	ON	19200	None	—
OFF	ON	ON	OFF	1200	Odd	—
OFF	ON	ON	ON	2400	Odd	—
ON	OFF	OFF	OFF	4800	Odd	—
ON	OFF	OFF	ON	9600	Odd	—
ON	OFF	ON	OFF	19200	Odd	—
ON	OFF	ON	ON	1200	Even	—
ON	ON	OFF	OFF	2400	Even	—
ON	ON	OFF	ON	4800	Even	—
ON	ON	ON	OFF	9600	Even	—
ON	ON	ON	ON	19200	Even	—

— 35 —

Image 38

Contents DOT Matrix Printer Weee Mark Declaration of Conformity General Precautions Ordinarymaintenance Page Precautions for Installation Precautions for Handling Table of Contents External Dimensions Introduction FeaturesAccessories Type Power supplyType Classifications Specifications CBM-920II-24 CBM-920II-40External Appearance and Part Descriptions External AppearancePart Descriptions Operations Rack MountingI/F Cable Connection Panel Opening/Closing Opening/Closing of Front PanelSetting Ribbon Cassette Paper FeedingSetting Paper Page Auto Loading Function Self-printing Function, Hexadecimal Printing Function Memory Switch Setting Japan 920JPN International 920IntlPage Contents of Memory Switch Setting CBM-920II 10 PNE, PE, Other errors State Clearing Lamp Status, I/F signal status, error, etcReturn Paper lamp Power lamp Signal line Special Functions Parallel Interface Connector Pin AssignmentPin Signal Name Description of Input/Output Signals Electrical Characteristics Host Side Printer SideSerial Interface TTL , Cmos Description of Input/Output Signal Dtrdata Terminal ReadyError Detection Receiving Control and BufferingSwitch No Function DIP Switch SW1 SettingDIP Switch Position Factory SettingSwitch No Baud Rate Parity Factory Setting Bps Serial Interface TypeList of Control Codes Symbol Code Function Emulation Hexadecimal CBM920 IDP3110Print Control Function Control Code Details SW1 Switch No.1SW2 Switch No.2 ABC Country Character Code TableESC Page FF FF FF FF FF FF For 40-column model 3 4 5 6 41H 22H 55H 08H 41H 00H 41H Model CBM-920 emulation For manual setting, refer to 4.9 Setting Memory Switch Setting range of parameters n1 and n2 is as shown below Function Content of SettingCharacter Code Table Code page tablePage Page Page International Character Code Table External Dimensions