Citizen Systems CBM920II user manual For manual setting, refer to 4.9 Setting Memory Switch

Page 50

2.iDP3110 emulation

In order to reduce power consumption when printer is not in operation, two power down modes triggered by the codes DC2 (12H) and DC3 (13H) are available with this printer.

When the printer receives DC2 (12H) or DC3 (13H), it enters the power down mode after all data previously received is printed out.

To exit the power down mode, re-enter the printer power or apply the “LOW” signal to the RESET terminal for more than 4 ms.

(a)DC2 (12H)

The printer enters the power down mode when DC3 (13H) code is entered. In this mode, the oscillator does not stop oscillation.

(b)DC3 (13H)

The printer enters the power down mode when DC2 (12H) code is entered. Operation of the oscillator is terminated, reducing the power consumption to less than that of the DC2 power down mode.

(17)Change Memory Switch (ESC + “)“) Command

By the entry of the ESC(1BH)+ “)”(29H)+55H+n1+n2+AAH code, contents of memory switch shown in the table below can be changed.

When receiving this code, the printer enters the BUSY state and writes specified data (value) to the memory switch.

In this case, the printer performs reset operation. Here, the input buffer/print buffer is cleared, all set values are restored to the initial value, and the contents of memory switch are read again.

This command cannot be executed consecutively. When two or more memory settings are changed, set the value one by one.

NOTE

•If the parameter value is other than specified, writing to memory switch is not carried out.

•If the first byte and the fourth byte of parameter is other than specified code, writing to memory switch is not carried out.

•In case of serial interface, communication bit length must be set to 8 bits. When set to other than 8 bits, the communication bit length must be set to 8 bits by manual setting or the like.

*For manual setting, refer to “4.9 Setting Memory Switch”.

— 47 —

Page 49 Page 51
Image 50
Page 49 Page 51
Contents DOT Matrix Printer Weee Mark Declaration of Conformity General Precautions Ordinarymaintenance Page Precautions for Installation Precautions for Handling Table of Contents External Dimensions Introduction FeaturesAccessories Type Power supplyType Classifications Specifications CBM-920II-24 CBM-920II-40External Appearance and Part Descriptions External AppearancePart Descriptions Operations Rack MountingI/F Cable Connection Panel Opening/Closing Opening/Closing of Front PanelSetting Ribbon Cassette Paper FeedingSetting Paper Page Auto Loading Function Self-printing Function, Hexadecimal Printing Function Memory Switch Setting Japan 920JPN International 920IntlPage Contents of Memory Switch Setting CBM-920II 10 PNE, PE, Other errors State Clearing Lamp Status, I/F signal status, error, etcReturn Paper lamp Power lamp Signal line Special Functions Parallel Interface Connector Pin AssignmentPin Signal Name Description of Input/Output Signals Electrical Characteristics Host Side Printer SideSerial Interface TTL , CmosDescription of Input/Output Signal Dtrdata Terminal ReadyError Detection Receiving Control and BufferingSwitch No Function DIP Switch SW1 SettingDIP Switch Position Factory SettingSwitch No Baud Rate Parity Factory Setting Bps Serial Interface TypeList of Control Codes Symbol Code Function Emulation Hexadecimal CBM920 IDP3110Print Control Function Control Code Details SW1 Switch No.1SW2 Switch No.2 ABC Country Character Code TableESC Page FF FF FF FF FF FF For 40-column model 3 4 5 6 41H 22H 55H 08H 41H 00H 41H Model CBM-920 emulation For manual setting, refer to 4.9 Setting Memory Switch Setting range of parameters n1 and n2 is as shown below Function Content of SettingCharacter Code Table Code page tablePage Page Page International Character Code Table External Dimensions
Top Page Image Contents