Citizen Systems PPU-231II manual ESC $ n1 n2, Default

Page 21

ESC $ n1 n2

[Function]	Specifying the absolute positions
[Code]	<1B>H<24>H<n1><n2>
[Range]	0	n1	255
	0	n2	255
[Outline]	The printing start position is specified with the number of dots
	(1/203 inch unit) from the beginning of a line.

•The number of dots is divided by 256, whose quotient is taken as “n2” and the residual as “n1”.

•Therefore, the printing start position is equal to n1 + n2 ⋅ 256 from the beginning of a line.

[Caution]	The basic calculation pitch is set by GS P. After the line feed
	width is set, if the basic calculation by GS P leaves a fraction,
	the fraction is corrected with the minimum pitch of the
	mechanism, and the remainder is omitted.
	In STANDARD MODE, this command uses the horizontal (Paper
	feed direction) basic calculation pitch (x).
	In PAGE MODE, this command acts differently depending on
	the start point:
	(1) If the start point specified by ESC T is top right or bottom
	left, the command uses the vertical (Paper feed direction)
	basic calculation pitch (y).
	(2) If the start point specified by ESC T is top left or bottom
	right , the command uses the horizontal (Perpendicular to
	the paper feed direction) basic calculation pitch (x).
	Specification beyond the end of the line is ignored.
[Default]	The initial value is not defined.
[See Also]	ESC \, GS P, GS \, GS $

— 19 —

Image 21

Contents Command Reference Revision Print Control Functions Command Function Mode CodeESC \ Function Mode CodeCommand relative to NV memory Range DefaultOutline ReferenceSee Also Command DetailsPrint Results See Also Sample Program Standard Mode ModePrint Result Can DLE EOT n Range OutlineExample Page See Also DLE ENQ n ESC FF ESC SP n Default See AlsoLprint Aaaaa + CHR$&HA ESC ! n Lprint CHR$&HA END ESC $ n1 n2 100 Gosub Setchr ESC % nESC & s n m a p s⋅ a m-n+1 Font a ESC * m n1 n2 d k IMG1 ESC n ESC ESC 3 n ESC = n ESC ? n Function Code Outline Sample Program Print Results ESC @ESC D n k NUL ESC E n ESC G n ESC J n ESC L ESC M n Definition valueDetails ESC R n ESC S ESC T n ESC V n Default Sample ProgramESC W xL xH yL yH dxL dxH dyL dyH CAN, ESC L, ESC T, GS P ESC \ nL nH ESC a n ESC c 3 n ESC c 4 n ESC c 5 n ESC d n ESC n n ’ ∝ ← n = Default Sample Program Print Results GS ! n Horizontal MagnificationVertical Magnification Default See Also See Also ESC $, ESC T, ESC W, ESC \, GS P, GS \ GS $ nL nHGS * n1 n2 d n1⋅ n2⋅ Next I Next J Return Definition GS a pL pH n mGS / m Specifying starting/ending macro definition GS a m n GS B n GS H n Print Results GS I n GS L nL nH GS P, GS W GS P x y GS R 0 n GS R 1 n GS S 1DH56Hm 1DH56Hmn GS W nL nH GS L, GS P GS \ nL nH GS n1 n2 n3 GS a n Paper feed state triggered by Feed switch DLE EOT, GS r GS f n Selecting bar code height D1 ...... dn D1 ..... dk NULFor For Standard ModeDefault Initial value is not defined For page ModeUPC-A Description of Bar Codes For print examples, refer toAscii This bar code consists of 103 bar code characters FNC4 Special charactersDescription of Bar Codes See Also DLE EOT, GS a GS r nGS v 0 m xL xH yL yH d1...dk When xL+xH ⋅ 256= GS w n Range FS g3 m a1 a2 a3 a4 nL nH d1…dkReference FS g4 m a1 a2 a3 a4 nL nH FS g3 P n m Page Q n xL xH yL yH d1…dk 1… xL xH yL yH d1…dk n Page Related Commands FS p