Citizen Systems PPU-231II manual ESC n n

Page 52

ESC n n

[Function]

Setting a remaining amount of printout

 

[Code]

<1B>H<6E>H<n>

 

[Range]

0 n 255 (“n” in the 2nd byte denotes this command.)

[Outline]

This command sets the remaining amount of printing after

 

detecting paper near end 1. n is set in cm.

 

[Caution]

• If the paper near end (PNE) sensor is disabled, this command

 

has no function.

 

 

• The set value and the remaining amount of printing are not

 

cleared by the initialize command (ESC @).

 

• If a value lower than the preset value is set during PNE

 

detection, the printer may stop printing.

 

 

• The set value remains valid until the printer is restarted or the

 

a new value is set.

 

[Default]

n=150 (150 cm)

 

[Sample Program]

LPRINT CHR$ (&H1B); “n”; CHR$ (100); ←

When setting the

 

 

remaining amount of

 

 

printing to 100 cm

— 50 —

Image 52
Contents Command Reference Revision Command Function Mode Code Print Control FunctionsFunction Mode Code ESC \Command relative to NV memory Default RangeOutline ReferenceCommand Details See AlsoPrint Results See Also Sample Program Mode Standard ModePrint Result Can Range Outline DLE EOT nExample Page See Also DLE ENQ n ESC FF Default See Also ESC SP nLprint Aaaaa + CHR$&HA ESC ! n Lprint CHR$&HA END ESC $ n1 n2 100 ESC % n Gosub SetchrESC & s n m a p s⋅ a m-n+1 Font a ESC * m n1 n2 d k IMG1 ESC n ESC ESC 3 n ESC = n ESC ? n ESC @ Function Code Outline Sample Program Print ResultsESC D n k NUL ESC E n ESC G n ESC J n ESC L Definition value ESC M nDetails ESC R n ESC S ESC T n Default Sample Program ESC V nESC W xL xH yL yH dxL dxH dyL dyH CAN, ESC L, ESC T, GS P ESC \ nL nH ESC a n ESC c 3 n ESC c 4 n ESC c 5 n ESC d n ESC n n ’ ∝ ← n = Default Sample Program Print Results Horizontal Magnification GS ! nVertical Magnification Default See Also GS $ nL nH See Also ESC $, ESC T, ESC W, ESC \, GS P, GS \GS * n1 n2 d n1⋅ n2⋅ Next I Next J Return GS a pL pH n m DefinitionGS / m Specifying starting/ending macro definition GS a m n GS B n GS H n Print Results GS I n GS L nL nH GS P, GS W GS P x y GS R 0 n GS R 1 n GS S 1DH56Hm 1DH56Hmn GS W nL nH GS L, GS P GS \ nL nH GS n1 n2 n3 GS a n Paper feed state triggered by Feed switch DLE EOT, GS r GS f n Selecting bar code height D1 ..... dk NUL D1 ...... dnFor Standard Mode ForFor page Mode Default Initial value is not definedDescription of Bar Codes For print examples, refer to UPC-AAscii This bar code consists of 103 bar code characters Special characters FNC4Description of Bar Codes GS r n See Also DLE EOT, GS aGS v 0 m xL xH yL yH d1...dk When xL+xH ⋅ 256= GS w n FS g3 m a1 a2 a3 a4 nL nH d1…dk RangeReference FS g4 m a1 a2 a3 a4 nL nH FS g3 P n m Page Q n xL xH yL yH d1…dk 1… xL xH yL yH d1…dk n Page Related Commands FS p