Citizen Systems PPU-231II manual ESC \ nL nH, Sample Program

Page 46

ESC \ nL nH

[Function]

Specifying the relative position

[Code]

<1B>H<5C>H<nL><nH>

[Range]

0

nL

255

 

0

nH

255

[Outline]

This command specifies the next print start position in a relative

 

position with respect to the current position. The next print start

 

position will be at a point of [(nL + nH 256) basic calculation

 

pitch] inches away from the current position.

[Caution]

• Specification of a position outside the print area is ignored.

If a new position is specified to the right of the current position in the direction of printing, it should be specified as positive

(+). If it is to the left, it should be as negative(-).

A negative value is the complement of 65536. For example, to move the position by N pitches to the left, specify it as:

nL + nH 256 = 65536 - N

The basic calculation pitch is set by GS P.

Fractions resulting from calculation are corrected with the minimum pitch of the mechanism, and the remainder is omitted.

In STANDARD MODE, this command uses the horizontal basic calculation pitch (x).

In PAGE MODE, this command acts differently depending on the start point:

(1)If the start point specified by ESC T is top left or bottom right, the command specifies the relative position in the direction perpendicular to the paper feed (The character’s side-to-side direction), using the horizontal basic calculation pitch (x).

(2)If the start point is top right or bottom left, the command specifies the relative position in the paper feed direction (The character’s side-to-side direction), using the vertical basic calculation pitch (y).

[See Also]

ESC $, GS P

[Sample Program]

Refer to Sample Program and Print Results for ESC $ on

 

page 21.

— 44 —

Image 46
Contents Command Reference Revision Command Function Mode Code Print Control FunctionsFunction Mode Code ESC \Command relative to NV memory Outline DefaultRange ReferenceCommand Details See AlsoPrint Results See Also Sample Program Mode Standard ModePrint Result Can Range Outline DLE EOT nExample Page See Also DLE ENQ n ESC FF Default See Also ESC SP nLprint Aaaaa + CHR$&HA ESC ! n Lprint CHR$&HA END ESC $ n1 n2 100 ESC % n Gosub SetchrESC & s n m a p s⋅ a m-n+1 Font a ESC * m n1 n2 d k IMG1 ESC n ESC ESC 3 n ESC = n ESC ? n ESC @ Function Code Outline Sample Program Print ResultsESC D n k NUL ESC E n ESC G n ESC J n ESC L Definition value ESC M nDetails ESC R n ESC S ESC T n Default Sample Program ESC V nESC W xL xH yL yH dxL dxH dyL dyH CAN, ESC L, ESC T, GS P ESC \ nL nH ESC a n ESC c 3 n ESC c 4 n ESC c 5 n ESC d n ESC n n ’ ∝ ← n = Default Sample Program Print Results Horizontal Magnification GS ! nVertical Magnification Default See Also GS $ nL nH See Also ESC $, ESC T, ESC W, ESC \, GS P, GS \GS * n1 n2 d n1⋅ n2⋅ Next I Next J Return GS a pL pH n m DefinitionGS / m Specifying starting/ending macro definition GS a m n GS B n GS H n Print Results GS I n GS L nL nH GS P, GS W GS P x y GS R 0 n GS R 1 n GS S 1DH56Hm 1DH56Hmn GS W nL nH GS L, GS P GS \ nL nH GS n1 n2 n3 GS a n Paper feed state triggered by Feed switch DLE EOT, GS r GS f n Selecting bar code height D1 ..... dk NUL D1 ...... dnFor Standard Mode ForFor page Mode Default Initial value is not definedDescription of Bar Codes For print examples, refer to UPC-AAscii This bar code consists of 103 bar code characters Special characters FNC4Description of Bar Codes GS r n See Also DLE EOT, GS aGS v 0 m xL xH yL yH d1...dk When xL+xH ⋅ 256= GS w n FS g3 m a1 a2 a3 a4 nL nH d1…dk RangeReference FS g4 m a1 a2 a3 a4 nL nH FS g3 P n m Page Q n xL xH yL yH d1…dk 1… xL xH yL yH d1…dk n Page Related Commands FS p