Citizen Systems PPU-231II manual GS \ nL nH

Page 77

GS \ nL nH

[Function]

Specifying the relative vertical position of a character in

 

PAGE MODE

[Code]

<1D>H<5C>H<nL><nH>

[Range]

0

nL

255

 

0

nH

255

[Outline]

This command is used in PAGE MODE to specify the vertical

 

position of a character in the data mapping start position, in a

 

relative position with respect to the current position. The next

 

data mapping start position will be at a point [(nL + nH 256)

 

basic calculation pitch] inches away from the current position.

[Caution]

• This command is ignored when PAGE MODE is not selected.

If a new position is specified for a character located beneath the current position, it should be specified as positive (+). If it is above the current position, it should be negative (-).

A negative value is the complement of 65536. For example, to move the position by N pitches up, specify it as:

nL + nH 256 = 65536 - N

The specification of a relative position outside the specified print area is ignored.

Depending on the start point specified by ESC T, this command acts as follows:

(1)If the start point is the top left or bottom right, the command specifies the relative position in the paper feed direction (The character’s top-bottom direction) using the vertical basic calculation pitch (y).

(2)If the start point is the top right or bottom left, the command specifies the relative position in the direction perpendicular to the paper feed (The character’s top-bottom direction) using the horizontal basic calculation pitch (x).

The basic calculation pitch is set by GS P.

Fractions resulting from calculations are corrected with the minimum pitch of the mechanism, and the remainder is omitted.

— 75 —

Image 77
Contents Command Reference Revision Print Control Functions Command Function Mode CodeESC \ Function Mode CodeCommand relative to NV memory Range DefaultOutline ReferenceSee Also Command DetailsPrint Results See Also Sample Program Print Result Standard ModeMode Can Example DLE EOT nRange Outline Page See Also DLE ENQ n ESC FF ESC SP n Default See AlsoLprint Aaaaa + CHR$&HA ESC ! n Lprint CHR$&HA END ESC $ n1 n2 100 Gosub Setchr ESC % nESC & s n m a p s⋅ a m-n+1 Font a ESC * m n1 n2 d k IMG1 ESC n ESC ESC 3 n ESC = n ESC ? n Function Code Outline Sample Program Print Results ESC @ESC D n k NUL ESC E n ESC G n ESC J n ESC L Details ESC M nDefinition value ESC R n ESC S ESC T n ESC V n Default Sample ProgramESC W xL xH yL yH dxL dxH dyL dyH CAN, ESC L, ESC T, GS P ESC \ nL nH ESC a n ESC c 3 n ESC c 4 n ESC c 5 n ESC d n ESC n n ’ ∝ ← n = Default Sample Program Print Results Vertical Magnification GS ! nHorizontal Magnification Default See Also See Also ESC $, ESC T, ESC W, ESC \, GS P, GS \ GS $ nL nHGS * n1 n2 d n1⋅ n2⋅ Next I Next J Return Definition GS a pL pH n mGS / m Specifying starting/ending macro definition GS a m n GS B n GS H n Print Results GS I n GS L nL nH GS P, GS W GS P x y GS R 0 n GS R 1 n GS S 1DH56Hm 1DH56Hmn GS W nL nH GS L, GS P GS \ nL nH GS n1 n2 n3 GS a n Paper feed state triggered by Feed switch DLE EOT, GS r GS f n Selecting bar code height D1 ...... dn D1 ..... dk NULFor For Standard ModeDefault Initial value is not defined For page ModeUPC-A Description of Bar Codes For print examples, refer toAscii This bar code consists of 103 bar code characters FNC4 Special charactersDescription of Bar Codes See Also DLE EOT, GS a GS r nGS v 0 m xL xH yL yH d1...dk When xL+xH ⋅ 256= GS w n Range FS g3 m a1 a2 a3 a4 nL nH d1…dkReference FS g4 m a1 a2 a3 a4 nL nH FS g3 P n m Page Q n xL xH yL yH d1…dk 1… xL xH yL yH d1…dk n Page Related Commands FS p