Opticon OPR 2001 Document History, Copyright 2007 Opticon. All rights reserved, Serial Number

Page 2

Opticon

OPR 2001

Specifications Manual

All information subject to change without notice.

Document History

Model Number:

OPR 2001

Specification Number:

 

 

 

Edition:

1

Original Spec Number:

 

 

 

Date:

2007-02-14

 

 

 

 

SS07011

SS06121

Copyright 2007 Opticon. All rights reserved.

This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon.

Limited Warranty and Disclaimers

PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT.

Serial Number

A serial number appears on all Opticon products. This official registration number is directly related to the device purchased. Do not remove the serial number from your Opticon device. Removing the serial number voids the warranty.

Warranty

Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in materials and workmanship for two years after purchase. Opticon will repair or, at its option, replace products that are defective in materials or workmanship with proper use during the warranty period. Opticon is not liable for damages caused by modifications made by a customer. In such cases, standard repair charges will apply. If a product is returned under warranty and no defect is found, standard repair charges will apply. Opticon assumes no liability for any direct, indirect, consequential or incidental damages arising out of use or inability to use both the hardware and software, even if Opticon has been informed about the possibility of such damages.

Packaging

The packing materials are recyclable. We recommend that you save all packing material to use should you need to transport your scanner or send it for service. Damage caused by improper packaging during shipment is not covered by the warranty.

Trademarks

Trademarks used are the property of their respective owners.

Opticon Inc. and Opticon Sensors Europe B.V. are wholly owned subsidiaries of OPTOELECTRONICS Co., Ltd., 5-3, Tsukagoshi 5-chome, Warabi-shi, Saitama, Japan 335-0002. TEL +81-(0) 48-446-1183; FAX +81-(0) 48-446-1180

SUPPORT

USA

Europe

Phone: 800-636-0090

 

Email: support@opticonusa.com

Email: support@opticon.com

Web: www.opticonusa.com

Web: www.opticon.com

 

 

2

Image 2
Contents OPR Document History Limited Warranty and DisclaimersWarranty Copyright 2007 Opticon. All rights reservedContents Cable and Connector Table of Figures Serial number diagram Abstract OverviewPhysical Features Environmental SpecificationsAmbient Light Immunity ConditionsRS-232C Electrical SpecificationsParameter Symbol Min Typ Max Unit USB, WedgeParameter Specification Optical SpecificationsLaser Scanning Specifications Laser Scanning Standard Laser Scanning TiltTechnical Specifications Print Contrast Signal PCSQuiet Zone Scan Area and ResolutionResolution Symbology Digits Depth of Field mmPitch, Skew, and Tilt Pitch Angle PitchSkew Angle and Dead Zone Skew angle and dead zoneTilt Angle Pitch, Skew Angle, Dead ZoneCurvature CurvatureSignal Level Interface SpecificationsRS-232C Interface Settings and Communication U2 settingInterface Circuit Signal PinPin Assignment Communication Format Handshaking Menu/CommandCharacter Format HandshakingFlow Control Time Out Menu/Command BUSY/READYCTS, TXD signal timing ModemACK/NAK Timeout Menu/Command ACK/NAKACK/NAK no Response ACK/NAK-No responseUSB a connector USB Interface Specifications SettingsConnectors USB-HIDDOS/V Wedge Interface Specification Settings Desktop PC When using external keyboardContact Number Signal Name DOS/V Host ConnectorDOS/V Keyboard Connector USB Cable Cable and ConnectorRS-232C Cable Pin No RS-232C Connector Specification Scanner SideWedge Cable WedgeUSB-HID Default Default SettingsRS-232C Default Wedge Default with external keyboardSymbology Read Transmit Default Settings 1 Readable CodesWedge Default without external keyboard Set Others CodeSymbology Read Transmit Calculate Set Others Code Default Settings 2 Read Options, Trigger, Buzzer Default SettingCollective Packaging Specification Packaging SpecificationsIndividual Packaging Specification Serial NumberShock Drop Test without packaging DurabilityElectrical Noise Drop Test with individual packagingDust and Drip Proof Vibration StrengthStatic Electricity Cable Strength Cable Pulling TestReliability Auto Trigger OptionAuto Trigger Settings Stand Only Trigger optionsAlways ManuallyRegulatory Compliance Laser SafetyProduct Safety EMCShock SafetyTemperature Conditions Foreign MaterialsMechanical Drawing Mechanical drawing