Lathem 7500E manual Limited One-Year Warranty

Page 49

Limited One-Year Warranty

Lathem warrants the hardware products described in this guide against defects in material and workmanship for a period of one year from date of original purchase from Lathem or from an authorized Lathem reseller. The conditions of this warranty and the extent of the responsibility of Lathem Time Corporation ("Lathem") under this warranty are listed below.

1.This warranty will become void when service performed by anyone other than an approved Lathem warranty service dealer results in damage to the product.

2.This warranty does not apply to any product which has been subject to abuse, neglect, or accident, or which has had the serial number altered or removed, or which has been connected, installed, adjusted, or repaired other than in accordance with instructions furnished by Lathem.

3.This warranty does not cover dealer labor cost for removing and reinstalling the machine for repair, or any expendable parts that are readily replaced due to normal use.

4.The sole responsibility of Lathem under this warranty shall be limited to repair of this product, or replacement thereof, at the sole discretion of Lathem.

5.If it becomes necessary to send the product or any defective part to Lathem or any authorized service dealer, the product must be shipped in its original carton or equivalent, fully insured with shipping charges prepaid. Lathem will not assume any responsibility for any loss or damage incurred in shipping.

6.WARRANTY DISCLAIMER AND LIMITATION OF LIABILITY: Except only the limited express warranty set forth above, the products are sold with no expressed or implied warranties of any kind, and the implied warranties of merchantability and fitness for a particular purpose are hereby expressly disclaimed. No warranties are given with respect to products purchased other than from Lathem or an authorized Lathem reseller and any such products are purchased "as is, with all faults." In no event will Lathem be liable for any direct, indirect, special, incidental or consequential damages arising out of or in connection with the delivery, use or inability to use, or performance of this product. In the event any limited remedy given herein shall be deemed to have failed of its essential purpose, Lathem's maximum liability shall be to refund the purchase price upon return of the product.

7.Proof of date of purchase from Lathem or an authorized Lathem reseller is required for warranty service on this product.

8.This Warranty grants specific legal rights. Additional legal rights, which may vary by locale, may also apply.

9.Should any difficulties arise with the performance of this product during warranty, or with any Lathem authorized service centers, contact Lathem Time at the address below.

Lathem Time

200 Selig Drive, SW, Atlanta, GA 30336

404-691-0405

www.lathem.com

Copyright © 2009 Lathem Time Corporation. All rights reserved.

45

46

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Page Time CORP. with all rights reserved Table of Contents Features AccessoriesIntroduction Installing Ribbon Cassette Quick SetupCorrect Wrong Set the Display Hours Setting the Display HoursSetting the Time Zone for Atomic Clock Function Default Settings Advanced Settings Contents Environmental Conditions Mounting Unit on WallLeave about 1/8 gap between wall and screw head Level Line Template for wall mountingSetting the Time Advanced SettingsSetting the Date Payroll Mode Setting the ModeSet the Starting day of the week Setting Weekly Period in Payroll ModeSet the Mode Setting Monthly Period in Payroll ModeSet the Starting date Setting Bi-Weekly Period in Payroll Mode Set the 1st starting date Setting Semi-Monthly Period in Payroll ModeSet the 2nd starting date Set the card Reset Job Cost ModeSet the Date/D.O.W. print format Setting the Print FormatSet the Minute print format for totals only Set the Hour print formatSpecial Note Regarding Punch Rounding Setting the RoundingSet the Rounding unit Set the Types of roundingTotal Setting the Auto Break DeductionSet the Elapsed time Set the Max In Override Setting the MaxSet the Max In Value Disabled Setting the Button Function In/OutRequired OptionalRequired Automatic DST correction Setting the Daylight Savings TimeYear Month Date Mark means Starting date setting Set the ending date Deleting the Daylight Savings Time settings Setting the Print Language Operations & Functions Radio Signal Reception Resetting Settings Resetting Cards In Job Cost Mode Card reassign All cards reset Card reset Print Example Installing Battery Optional Error No. Causes and Actions TroubleshootingQuestions Troubleshooting Questions & AnswersDaily Care Specifications Limited One-Year Warranty Form No. OM75E0909 Q0280-61200
Top Page Image Contents