Trango Broadband Wireless: Essential Guide to Basic Configuration of M900S Router

Page 18

Basic Configuration via Browser Interface

Configure Basic SU Parameters

In order to establish a working link, the Base ID in the SU must match the Base ID set in the AP.

SU Basic Setup:

1.Connect to the SU (see Getting Started) and open the Configuration page.

2.Set Base ID. (Must match the AP.)

3.Set IP, Subnet, and Gateway, or leave at default settings. Keep in mind, if you change the IP Settings of the radio, you will loose your HTTP session when you Save and Activate Settings.

4.Ensure default Opmode is "ON."

5.Save and Activate Settings.

6.If in Opmode “OFF,” click Activate Opmode.

At this point, if all parameters have been set correctly and the radios are within range, a wireless link between the AP and SU will automatically become established. Once this occurs the SU will be in “associated” status.

Allow approximately 60 seconds for the radios to complete the boot-up cycle and to associate. If the AP is busy servicing many SUs, the association process may take slightly longer.

Trango Broadband Wireless — User Manual M900S Rev. C

Page 14

Image 18
Contents M900S MHz Wireless Broadband System Table of Contents Table of Figures FCC Information Warranty Information Firmware NotificationsPreface CanadaIntroduction OverviewAuto-retransmit Feature ARQ SmartPolling & Bandwidth ThrottlingHardware Overview M900S AP and SU Hardware ComponentsConnections and Power Getting StartedRadio Management Concepts CAT-5Switch Settings Browser InterfaceBrowser Interface Login Web Browser System InformationCommand Line Interface Telnet ip address of radioTroubleshooting Basic Configuration via Browser Interface Configuring the AP’s Subscriber Unit Database SudbThis section you will Creating an SU in the SU Database IP Address, Subnet Mask, Gateway Configure Other Basic AP ParametersDefault Opmode Active Channel/PolarizationBasic Configuration via Browser Interface Configure Basic SU Parameters SU Basic SetupLED Summary LED SummaryRF Link Loopback Test Link ControlAdvanced Setup SU Ranging TestOther Key Parameters Site Survey AP Parameter Description Related CLI Command Basic Configuration via CLIAccess Point Basic Settings Set baseid baseidIpconfig new ip new subnet mask new Set defaultopmode on or offSet defaultopmode on time sec Set apid apid 00-FF in HEXOn/off command Power set minmaxdBmSw 0 onoff default is on Sw 3 onoff default is offRemarks remarks Subscriber Unit Database Sudb SettingsSw 7 onoff default is on Sudb add suid prreg device id suid SU IDSubscriber Unit Basic Settings Basic Configuration via CLI Ipconfig new ip new subnet mask new SU Parameter Description Related CLI CommandSet defaultopmode on or off Set baseid baseidSw 1 onoff Antenna h v eSw 0 onoff Sw 2 onoffM900S Mounting Hardware Assembly Mounting HardwareAlternative Mounting Cabling and Grounding Considerations Standard Mounting Alternative MountingInstallation Notes Command survey time antenna DeploymentSite Selection AP Search and SU Antenna Alignment Example\Rssi Command for Antenna Alignment SU Alignment Using LEDsAP Search Link Management Commands Collocation and Channel PlanningSu ping su# Su su #Su linktest su# Su testrflink su#ARQ with Selected Repeat and Multirate Feature Management Radio Management Access Via TCP/IPSu password suid all rw ro new password new password SU Management from APLoading Multiple SUs into the Sudb using Dload Command SnmpObjects for Monitoring and Control SU Bandwidth MonitoringAP Bandwidth Monitoring Snmp Setup Appendix a Command Set Reference Command Radio DescriptionCommand Radio Description Access Su ipconfig suid new IP new Command Radio Description Access Receiver Specifications Appendix B SpecificationsRadio Transmit Specifications Ethernet I/O Specifications Data Input/OutputConnectors/Indicators Power SpecificationsMechanical and Environmental Specifications General Standard External Power SupplyIntegrated Antenna M900S-SU and M900S-SU-EXT