Trango Broadband user manual Integrated Antenna M900S-SU and M900S-SU-EXT

Page 53

Eth. Out & DC Out:

Shielded RJ-45 Jack

Pinout for Eth. Out:

Power (+) on pins 7+8, ground (-) on pins 4+5 and eth. data on pins 1,2,3 & 6

Indicators:

2 LEDs to indicate power and a connection to radio

Protection:

Resettable fuse for DC input

Integrated Antenna (M900S-SU and M900S-SU-EXT)

Type:

Air-loaded Patch Antenna

Polarization:

Vertical or Horizontal Polarization, electrically selectable

Frequency:

902 to 928 MHz

Gain:

+10 +/- 1 dBiL

Az Beamwidth:

60º (3 dB pts)

El Beamwidth:

60º (3 dB pts)

Cross Pol:

>15 dB

Front/Back Ratio:

12 dB

VSWR:

< 2.0:1 over Bandwidth

Trango Broadband Wireless — User Manual M900S Rev. C

Page 49

Image 53
Contents M900S MHz Wireless Broadband System Table of Contents Table of Figures Preface Warranty Information Firmware NotificationsFCC Information CanadaOverview IntroductionSmartPolling & Bandwidth Throttling Auto-retransmit Feature ARQM900S AP and SU Hardware Components Hardware OverviewGetting Started Connections and PowerCAT-5 Radio Management ConceptsBrowser Interface Switch SettingsWeb Browser System Information Browser Interface LoginTelnet ip address of radio Command Line InterfaceTroubleshooting This section you will Basic Configuration via Browser InterfaceConfiguring the AP’s Subscriber Unit Database Sudb Creating an SU in the SU Database Default Opmode Configure Other Basic AP ParametersIP Address, Subnet Mask, Gateway Active Channel/PolarizationBasic Configuration via Browser Interface SU Basic Setup Configure Basic SU ParametersLED Summary LED SummaryLink Control RF Link Loopback TestSU Ranging Test Advanced SetupOther Key Parameters Site Survey Access Point Basic Settings Basic Configuration via CLIAP Parameter Description Related CLI Command Set baseid baseidSet defaultopmode on time sec Set defaultopmode on or offIpconfig new ip new subnet mask new Set apid apid 00-FF in HEXSw 0 onoff default is on Power set minmaxdBmOn/off command Sw 3 onoff default is offSw 7 onoff default is on Subscriber Unit Database Sudb SettingsRemarks remarks Sudb add suid prreg device id suid SU IDSubscriber Unit Basic Settings Basic Configuration via CLI Set defaultopmode on or off SU Parameter Description Related CLI CommandIpconfig new ip new subnet mask new Set baseid baseidSw 0 onoff Antenna h v eSw 1 onoff Sw 2 onoffMounting Hardware M900S Mounting Hardware AssemblyAlternative Mounting Standard Mounting Alternative Mounting Cabling and Grounding ConsiderationsInstallation Notes Site Selection Command survey time antennaDeployment Example\ AP Search and SU Antenna AlignmentAP Search Rssi Command for Antenna AlignmentSU Alignment Using LEDs Collocation and Channel Planning Link Management CommandsSu su # Su ping su#Su testrflink su# Su linktest su#ARQ with Selected Repeat and Multirate Feature Su password suid all rw ro new password new password Radio Management Access Via TCP/IPManagement SU Management from APSnmp Loading Multiple SUs into the Sudb using Dload CommandAP Bandwidth Monitoring Objects for Monitoring and ControlSU Bandwidth Monitoring Snmp Setup Command Radio Description Appendix a Command Set ReferenceCommand Radio Description Access Su ipconfig suid new IP new Command Radio Description Access Radio Transmit Specifications Appendix B SpecificationsReceiver Specifications Ethernet I/O Specifications Data Input/OutputMechanical and Environmental Specifications General Power SpecificationsConnectors/Indicators Standard External Power SupplyIntegrated Antenna M900S-SU and M900S-SU-EXT