Command | Radio | Description | Access | |||
|
|
| 21. | TX power |
|
|
|
|
| 22. | Remarks |
|
|
|
|
| 23. RF TX retry at AP, RF TX retry maxed out at AP |
|
| |
|
|
| RF TX retry at SU, RF TX retry maxed out at SU |
|
| |
su ipconfig <suid> <new IP> <new | AP | Change IP, subnet, gateway for specified SU | rw | |||
subnet> <new gateway> |
|
|
|
|
| |
su linktest <suid> | AP | Perform linktest for specified SU | ro/rw | |||
su ping <suid> | AP | Request SU’s ranging and RSSI information | ro/rw | |||
su reboot <all suid> | AP | Reboot a specific SU or all SUs | rw | |||
su sw <suid> <sw #> <on off> | AP | Change switch settings on specified SU | rw | |||
sudb add <suid> <prre> <mac> | AP | Add new SU to SUDB | rw | |||
sudb cirmir <<suid>all> <cir dn> <cir up> | AP | Change SU’s CIR/MIR settings | rw | |||
<mir dn> <mir up> |
|
|
|
|
| |
sudb defaultcirmir | AP | Display default CIR and MIR in SUDB | ro/rw | |||
sudb defaultcirmir <cir_dn, 0..3000> <cir_up, | AP | Change default CIR and MIR | rw | |||
0..3000> <mir_dn, 0..3000> <mir_up, 0..3000> |
|
|
|
|
| |
sudb defaultcirmir <default cir dn> <default cir | AP | Set MIR/CIR values to default values | rw | |||
up> <default mir dn> <default mir up> |
|
|
|
|
| |
sudb delete <suid all> | AP | Delete SU in SUDB | rw | |||
sudb dload | AP | Download SUDB file from TFTP buffer and write to flash memory. | rw | |||
|
|
| This command is used to load a text file that contains the SUDB into |
|
| |
|
|
| the AP. This command can be useful if there are large numbers of |
|
| |
|
|
| SUs in the sector. |
|
| |
sudb gid <suid all> <0..15> | AP | Change SU’s gid | rw | |||
sudb view | AP | Display all SUDB | ro/rw | |||
survey <search time, sec> <antenna, h v e> | AP/SU | Spectrum analysis of the entire band (and near band) | ro/rw | |||
|
|
| <search time> = 1..10 sec per channel |
|
| |
|
|
| Opmode “OFF” only |
|
| |
Sw | AP/SU | Display current sw setting | ro/rw | |||
sw 0 [<on off>] | AP/SU | set sw #0 – enable or disable packet filter for broadcast/ multicast | rw | |||
|
|
| packets |
|
|
|
|
|
| on = filtering |
|
| |
|
|
| default = on |
|
| |
sw 1 [<on off>] | SU | Enable or disable SU’s autoscan AP feature | rw | |||
|
|
| If on, SU will automatically scan each channel and antenna port |
|
| |
|
|
| searching for AP. |
|
| |
|
|
| default=on |
|
| |
|
|
| Note: Recommended setting for |
|
| |
sw 2 [<on off>] | SU | Enable or disable SU’s TCP/IP service for AP | rw | |||
|
|
| Allows TCP/IP access to SU from AP side of network via wireless |
|
| |
|
|
| link. |
|
|
|
|
|
| default = on |
|
| |
sw 3 [<on off>] | AP | Enable or disable SU to SU (peer to peer) service | rw | |||
|
|
| default = off |
|
| |
sw 5 [<on off>] | AP/SU | Enable or disable HTTPD (browser interface) | rw | |||
|
|
| default = on |
|
| |
sw 6 [<on off>] | SU | Enable or disable TCP/IP service for Ethernet port while SU is in | rw | |||
|
|
| Opmode “ON” |
|
| |
|
|
| default = on |
|
| |
sw 7 [<on off>] | AP | Enable or disable TCP/IP service for SU. Allows TCP/IP access to | rw | |||
|
|
| AP from SU side of network via wireless link. |
|
| |
|
|
| default = on |
|
| |
sysinfo | AP/SU | Display system configuration | ro/rw | |||
targetap | SU | Display the SU current setting for target AP | ro/rw | |||
targetap all | SU | SU will associate with any AP with the same Base ID | rw | |||
|
|
| “all” is the default setting. |
|
| |
targetap only <mac1, hex> [<mac2, hex>] | SU | SU will only associate with AP with specified MAC addresses. | rw | |||
targetrssi | AP | Display SU Target RSSI in dBm. This setting is used in the SU | ro/rw | |||
|
|
| power leveling process. |
|
| |
|
|
|
|
|
|
|
| Trango Broadband Wireless — User Manual M900S Rev. C |
| Page 45 | |||