Trango Broadband M900S SU Parameter Description Related CLI Command, Set baseid baseid, Gateway

Page 30

Basic Configuration via CLI

SU SYSTEM INFORMATION PARAMETERS AND RELATED COMMANDS

 

SU Parameter

Description

Related CLI Command

 

Device ID

MAC Address of the SU

N/A

 

Base ID

Specifies the cell or cluster to

set baseid <baseid>

 

 

which the SU belongs.

Example:

 

 

 

 

 

 

#>Set baseid aa12

 

 

 

 

 

Target AP

If unique AP ID selected, the

targetap <apid>

 

SU can only associate with

 

 

 

the specified AP. If ALL is

 

 

 

selected, the SU can

Examples:

 

 

associate with any AP with a

#>targetap 33

 

 

matching BASE ID.

#>targetap all

 

Opmode

Current Opmode of radio.

opmode on y - set Opmode to “ON.” (note: “y”

 

 

 

is necessary if default Opmode is “OFF.”)

 

 

 

opmode off – set Opmode to “OFF.”

 

 

 

 

 

Default Opmode

Determines the Opmode

set defaultopmode <on or off>

 

(“ON” or “OFF”) of the radio

 

 

 

after reboot/power cycle.

Example:

 

 

When this parameter is set to

#>set defaultopmode on

 

 

“ON,” the radio will progress

 

 

 

into Opmode “ON”

 

 

 

automatically after

 

 

 

reboot/power cycle.

 

 

IP

IP, Subnet, and Gateway

ipconfig [<new ip> <new subnet mask> <new

 

Subnet

address of radio.

gateway>]

 

Gateway

 

Example:

 

 

 

 

 

 

#>ipconfig 10.1.1.3 255.0.0.0 10.1.1.1

 

 

 

 

 

TFTPD

TFTPD status (on or off).

tftpd [<onoff>]

 

TFTPD should be turned on

Example:

 

 

to import a file into the radio

#>tftpd on

 

 

(such as new firmware).

 

 

 

Default is off. TFTPD will

 

 

 

revert to off after

 

 

 

reboot/power cycle.

 

 

RF TX Power

Current transmit power of the

Informational Parameter – can not be manually

 

 

SU not including antenna

changed by user.

 

 

gain. This is controlled by

 

 

 

the AP.

 

 

Active Channel

Shows the channel used in

If Autoscan AP (SW 1) is on, the active channel

 

 

the current association, and

(and antenna selection) will be set once the SU

 

 

"Associated" or

scans and begins the association process with an

 

 

"Disconnected" depending

AP.

 

 

on the association status.

If Autoscan AP is off, the active channel is set by

 

 

 

the user, using the freq command.

 

 

 

freq [<ch#> <vh>]

 

 

 

Example:

 

 

 

#>freq 3

 

 

 

This command will change the channel of the AP to

 

 

 

3. Use the antenna command to select an antenna

 

 

 

 

 

Trango Broadband Wireless — User Manual M900S Rev C

Page 26

Image 30
Contents M900S MHz Wireless Broadband System Table of Contents Table of Figures FCC Information Warranty Information Firmware NotificationsPreface CanadaIntroduction OverviewAuto-retransmit Feature ARQ SmartPolling & Bandwidth ThrottlingHardware Overview M900S AP and SU Hardware ComponentsConnections and Power Getting StartedRadio Management Concepts CAT-5Switch Settings Browser InterfaceBrowser Interface Login Web Browser System InformationCommand Line Interface Telnet ip address of radioTroubleshooting Basic Configuration via Browser Interface Configuring the AP’s Subscriber Unit Database SudbThis section you will Creating an SU in the SU Database IP Address, Subnet Mask, Gateway Configure Other Basic AP ParametersDefault Opmode Active Channel/PolarizationBasic Configuration via Browser Interface Configure Basic SU Parameters SU Basic SetupLED Summary LED SummaryRF Link Loopback Test Link ControlAdvanced Setup SU Ranging TestOther Key Parameters Site Survey AP Parameter Description Related CLI Command Basic Configuration via CLIAccess Point Basic Settings Set baseid baseidIpconfig new ip new subnet mask new Set defaultopmode on or offSet defaultopmode on time sec Set apid apid 00-FF in HEXOn/off command Power set minmaxdBmSw 0 onoff default is on Sw 3 onoff default is offRemarks remarks Subscriber Unit Database Sudb SettingsSw 7 onoff default is on Sudb add suid prreg device id suid SU IDSubscriber Unit Basic Settings Basic Configuration via CLI Ipconfig new ip new subnet mask new SU Parameter Description Related CLI CommandSet defaultopmode on or off Set baseid baseidSw 1 onoff Antenna h v eSw 0 onoff Sw 2 onoffM900S Mounting Hardware Assembly Mounting HardwareAlternative Mounting Cabling and Grounding Considerations Standard Mounting Alternative MountingInstallation Notes Command survey time antenna DeploymentSite Selection AP Search and SU Antenna Alignment Example\Rssi Command for Antenna Alignment SU Alignment Using LEDsAP Search Link Management Commands Collocation and Channel PlanningSu ping su# Su su #Su linktest su# Su testrflink su#ARQ with Selected Repeat and Multirate Feature Management Radio Management Access Via TCP/IPSu password suid all rw ro new password new password SU Management from APLoading Multiple SUs into the Sudb using Dload Command SnmpObjects for Monitoring and Control SU Bandwidth MonitoringAP Bandwidth Monitoring Snmp Setup Appendix a Command Set Reference Command Radio DescriptionCommand Radio Description Access Su ipconfig suid new IP new Command Radio Description Access Receiver Specifications Appendix B SpecificationsRadio Transmit Specifications Ethernet I/O Specifications Data Input/OutputConnectors/Indicators Power SpecificationsMechanical and Environmental Specifications General Standard External Power SupplyIntegrated Antenna M900S-SU and M900S-SU-EXT