Trango Broadband M900S user manual Appendix B Specifications, Radio Transmit Specifications

Page 51

Appendix B Specifications

All specifications apply to the M900S-AP and M900S-SU, unless otherwise noted.

Radio Transmit Specifications

Storable Channels:

4 memory locations

 

Agility:

906 to 924 MHz in 1 MHz increments

 

Default channels:

 

 

Channel 1:

906 MHz

 

Channel 2:

912 MHz

 

Channel 3:

918 MHz

 

Channel 4:

924 MHz

 

Power Control Range:

Max: +26 dBm +/- 1

 

 

Min: -4 dBm +/- 2

 

 

Step: 1 dB

 

Pout:

+26 dBm max

 

Ant. Gain:

10 dBi

 

EIRP:

+36 dBm (4 Watt)

 

Freq. Stability:

+/- 1.5 ppm PLL stabilized (+/-2.5ppm) over temperature

 

Freq. Plan:

Single upconversion, 140 MHz IF

 

Modulated BW:

6.2 MHz (null to null, 40 dB down)

 

2nd Harmonic atten:

Per CFR47 part 15.407

 

LO Supression:

Per CFR47 part 15.407

 

Receiver Specifications

 

 

Storable Channels:

4 memory locations

 

Agility:

906 to 924 MHz in 1 MHz increments

 

Default channels:

 

 

Channel 1:

906 MHz

 

Channel 2:

912 MHz

 

Channel 3:

918 MHz

 

Channel 4:

924 MHz

 

Cascade Noise Figure:

< 7 dB

 

Receiver Sensitivity:

 

 

3.250 MBPS Rate:

- 88 dBm typical-1600 byte packet

 

(1x10-6BER)

- 88 dBm typical-64 byte packet

 

1.625 MBPS Rate:

- 91 dBm typical-1600 byte packet

 

(1x10-6BER)

- 91 dBm typical-64 byte packet

 

Image Rejection:

> 90 dB

 

Frequency Plan:

Single conversion, IF at 140 MHz

 

LO stability:

+/- 1.5 ppm PLL stabilized (+/-2.5ppm) over temperature

 

Ethernet I/O Specifications

 

Data Input/Output:

 

 

Connector:

Shielded RJ-45 Jack

 

Signaling Format:

IEEE802.3i (10baseT) and IEEE802.3u (100baseT) compliant

 

 

 

Trango Broadband Wireless — User Manual M900S Rev. C

Page 47

Image 51
Contents M900S MHz Wireless Broadband System Table of Contents Table of Figures Canada Warranty Information Firmware NotificationsPreface FCC InformationOverview IntroductionSmartPolling & Bandwidth Throttling Auto-retransmit Feature ARQM900S AP and SU Hardware Components Hardware OverviewGetting Started Connections and PowerCAT-5 Radio Management ConceptsBrowser Interface Switch SettingsWeb Browser System Information Browser Interface LoginTelnet ip address of radio Command Line InterfaceTroubleshooting Basic Configuration via Browser Interface Configuring the AP’s Subscriber Unit Database SudbThis section you will Creating an SU in the SU Database Active Channel/Polarization Configure Other Basic AP ParametersDefault Opmode IP Address, Subnet Mask, GatewayBasic Configuration via Browser Interface SU Basic Setup Configure Basic SU ParametersLED Summary LED SummaryLink Control RF Link Loopback TestSU Ranging Test Advanced SetupOther Key Parameters Site Survey Set baseid baseid Basic Configuration via CLIAccess Point Basic Settings AP Parameter Description Related CLI CommandSet apid apid 00-FF in HEX Set defaultopmode on or offSet defaultopmode on time sec Ipconfig new ip new subnet mask newSw 3 onoff default is off Power set minmaxdBmSw 0 onoff default is on On/off commandSudb add suid prreg device id suid SU ID Subscriber Unit Database Sudb SettingsSw 7 onoff default is on Remarks remarksSubscriber Unit Basic Settings Basic Configuration via CLI Set baseid baseid SU Parameter Description Related CLI CommandSet defaultopmode on or off Ipconfig new ip new subnet mask newSw 2 onoff Antenna h v eSw 0 onoff Sw 1 onoffMounting Hardware M900S Mounting Hardware AssemblyAlternative Mounting Standard Mounting Alternative Mounting Cabling and Grounding ConsiderationsInstallation Notes Command survey time antenna DeploymentSite Selection Example\ AP Search and SU Antenna AlignmentRssi Command for Antenna Alignment SU Alignment Using LEDsAP Search Collocation and Channel Planning Link Management CommandsSu su # Su ping su#Su testrflink su# Su linktest su#ARQ with Selected Repeat and Multirate Feature SU Management from AP Radio Management Access Via TCP/IPSu password suid all rw ro new password new password ManagementSnmp Loading Multiple SUs into the Sudb using Dload CommandObjects for Monitoring and Control SU Bandwidth MonitoringAP Bandwidth Monitoring Snmp Setup Command Radio Description Appendix a Command Set ReferenceCommand Radio Description Access Su ipconfig suid new IP new Command Radio Description Access Ethernet I/O Specifications Data Input/Output Appendix B SpecificationsRadio Transmit Specifications Receiver SpecificationsStandard External Power Supply Power SpecificationsMechanical and Environmental Specifications General Connectors/IndicatorsIntegrated Antenna M900S-SU and M900S-SU-EXT