Trango Broadband M900S user manual Command Radio Description Access

Page 50

Command	Radio	Description		Access
targetrssi <dBm, -90..-50>	AP	Change target RSSI. Note: Target RSSI must be +5 dB more than		rw
		rfrxth (RFRX Threshold).
		default = -60
tftpd	AP/SU	display current TFTPD status (status is either on or off) This		ro/rw
		command will also list any contents of the TFTP buffer.
tftpd <on off>	AP/SU	enable or disable TFTPD service. TFTPD must be on in order to		rw
		upload new firmware or new SUDB file.
updateflash <systemsetting ss>	AP/SU	Save current settings. This command can be issued in several ways:		rw
		save ss, updateflash systemsetting, save systemsetting, and
		updateflash ss
updateflash <mainimage fpgaimage>	AP/SU	Retrieve uploaded firmware from TFTP buffer, verify checksum,		rw
<current chscksum> <new checksum>		and write to flash memory at main or FPGA image section.

updateflash sudb	AP	Save SUDB into flash memory		rw
ver	AP/SU	Display firmware and date codes		ro/rw
		1.	Version number and date code
		2.	Firmware and FPGA version code
		3.	Firmware and FPGA image checksum

Trango Broadband Wireless — User Manual M900S Rev. C

Page 46

Image 50

Contents M900S MHz Wireless Broadband System Table of Contents Table of Figures FCC Information Warranty Information Firmware NotificationsPreface CanadaIntroduction OverviewAuto-retransmit Feature ARQ SmartPolling & Bandwidth ThrottlingHardware Overview M900S AP and SU Hardware ComponentsConnections and Power Getting StartedRadio Management Concepts CAT-5Switch Settings Browser InterfaceBrowser Interface Login Web Browser System InformationCommand Line Interface Telnet ip address of radioTroubleshooting This section you will Basic Configuration via Browser InterfaceConfiguring the AP’s Subscriber Unit Database Sudb Creating an SU in the SU Database IP Address, Subnet Mask, Gateway Configure Other Basic AP ParametersDefault Opmode Active Channel/PolarizationBasic Configuration via Browser Interface Configure Basic SU Parameters SU Basic SetupLED Summary LED SummaryRF Link Loopback Test Link ControlAdvanced Setup SU Ranging TestOther Key Parameters Site Survey AP Parameter Description Related CLI Command Basic Configuration via CLIAccess Point Basic Settings Set baseid baseidIpconfig new ip new subnet mask new Set defaultopmode on or offSet defaultopmode on time sec Set apid apid 00-FF in HEXOn/off command Power set minmaxdBmSw 0 onoff default is on Sw 3 onoff default is offRemarks remarks Subscriber Unit Database Sudb SettingsSw 7 onoff default is on Sudb add suid prreg device id suid SU IDSubscriber Unit Basic Settings Basic Configuration via CLI Ipconfig new ip new subnet mask new SU Parameter Description Related CLI CommandSet defaultopmode on or off Set baseid baseidSw 1 onoff Antenna h v eSw 0 onoff Sw 2 onoffM900S Mounting Hardware Assembly Mounting HardwareAlternative Mounting Cabling and Grounding Considerations Standard Mounting Alternative MountingInstallation Notes Site Selection Command survey time antennaDeployment AP Search and SU Antenna Alignment Example\AP Search Rssi Command for Antenna AlignmentSU Alignment Using LEDs Link Management Commands Collocation and Channel PlanningSu ping su# Su su #Su linktest su# Su testrflink su#ARQ with Selected Repeat and Multirate Feature Management Radio Management Access Via TCP/IPSu password suid all rw ro new password new password SU Management from APLoading Multiple SUs into the Sudb using Dload Command SnmpAP Bandwidth Monitoring Objects for Monitoring and ControlSU Bandwidth Monitoring Snmp Setup Appendix a Command Set Reference Command Radio DescriptionCommand Radio Description Access Su ipconfig suid new IP new Command Radio Description Access Receiver Specifications Appendix B SpecificationsRadio Transmit Specifications Ethernet I/O Specifications Data Input/OutputConnectors/Indicators Power SpecificationsMechanical and Environmental Specifications General Standard External Power SupplyIntegrated Antenna M900S-SU and M900S-SU-EXT