Trango Broadband M900S Set apid apid 00-FF in HEX, Opmode on y, Set defaultopmode on or off

Page 25

Basic Configuration via CLI

AP SYSTEM INFORMATION PARAMETERS AND RELATED COMMANDS

AP Parameter

Description

Related CLI Command

AP ID

This parameter provides a

set apid <apid> (00-FF in HEX)

 

unique number for each AP. If

 

 

Target AP is specified on SU,

Example:

 

the SU can only authenticate

#>set apid 33

 

with the specified AP. The

 

 

default AP ID is the last two

 

 

bytes of the MAC address.

 

Opmode

Current Opmode of the radio.

opmode on y

 

 

This sets the radio to Opmode “ON.” If the radio is

 

 

accessed via the Ethernet port within the first 30

 

 

seconds after reboot/power cycle, the Opmode will

 

 

default to “OFF.”

Default Opmode

Determines the Opmode (“ON”

set defaultopmode <on or off>

 

or “OFF”) of the radio after

Example:

 

reboot/power cycle. When this

 

parameter is set to “ON,” the

#>set defaultopmode on

 

radio will progress into

 

 

Opmode “ON” automatically

 

 

after a reboot/power cycle.

 

Opmode Start

Determines the amount of time

set defaultopmode on [<time (sec)>]

 

the radio will remain in

Example:

 

Opmode “OFF” after

 

reboot/power cycle before

#>set defaultopmode on 60

 

progressing to the default

 

 

Opmode.

 

IP

IP, Subnet, and Gateway

ipconfig [<new ip> <new subnet mask> <new

Subnet

address of the radio.

gateway>]

Gateway

 

Example:

 

 

 

 

#>ipconfig 10.1.1.2 255.0.0.0 10.1.1.1

TFTPD Status

TFTPD status (on or off).

tftpd [<onoff>]

 

TFTPD should be turned on to

Example:

 

import a file into the radio

#>tftpd on

 

(such as new firmware).

 

 

Default is off. TFTPD will

 

 

revert to Off after rebooting.

 

Trango Broadband Wireless — User Manual M900S Rev C

Page 21

Image 25
Contents M900S MHz Wireless Broadband System Table of Contents Table of Figures Preface Warranty Information Firmware NotificationsFCC Information CanadaOverview IntroductionSmartPolling & Bandwidth Throttling Auto-retransmit Feature ARQM900S AP and SU Hardware Components Hardware OverviewGetting Started Connections and PowerCAT-5 Radio Management ConceptsBrowser Interface Switch SettingsWeb Browser System Information Browser Interface LoginTelnet ip address of radio Command Line InterfaceTroubleshooting Configuring the AP’s Subscriber Unit Database Sudb Basic Configuration via Browser InterfaceThis section you will Creating an SU in the SU Database Default Opmode Configure Other Basic AP ParametersIP Address, Subnet Mask, Gateway Active Channel/PolarizationBasic Configuration via Browser Interface SU Basic Setup Configure Basic SU ParametersLED Summary LED SummaryLink Control RF Link Loopback TestSU Ranging Test Advanced SetupOther Key Parameters Site Survey Access Point Basic Settings Basic Configuration via CLIAP Parameter Description Related CLI Command Set baseid baseidSet defaultopmode on time sec Set defaultopmode on or offIpconfig new ip new subnet mask new Set apid apid 00-FF in HEXSw 0 onoff default is on Power set minmaxdBmOn/off command Sw 3 onoff default is offSw 7 onoff default is on Subscriber Unit Database Sudb SettingsRemarks remarks Sudb add suid prreg device id suid SU IDSubscriber Unit Basic Settings Basic Configuration via CLI Set defaultopmode on or off SU Parameter Description Related CLI CommandIpconfig new ip new subnet mask new Set baseid baseidSw 0 onoff Antenna h v eSw 1 onoff Sw 2 onoffMounting Hardware M900S Mounting Hardware AssemblyAlternative Mounting Standard Mounting Alternative Mounting Cabling and Grounding ConsiderationsInstallation Notes Deployment Command survey time antennaSite Selection Example\ AP Search and SU Antenna AlignmentSU Alignment Using LEDs Rssi Command for Antenna AlignmentAP Search Collocation and Channel Planning Link Management CommandsSu su # Su ping su#Su testrflink su# Su linktest su#ARQ with Selected Repeat and Multirate Feature Su password suid all rw ro new password new password Radio Management Access Via TCP/IPManagement SU Management from APSnmp Loading Multiple SUs into the Sudb using Dload CommandSU Bandwidth Monitoring Objects for Monitoring and ControlAP Bandwidth Monitoring Snmp Setup Command Radio Description Appendix a Command Set ReferenceCommand Radio Description Access Su ipconfig suid new IP new Command Radio Description Access Radio Transmit Specifications Appendix B SpecificationsReceiver Specifications Ethernet I/O Specifications Data Input/OutputMechanical and Environmental Specifications General Power SpecificationsConnectors/Indicators Standard External Power SupplyIntegrated Antenna M900S-SU and M900S-SU-EXT