Trango Broadband M900S user manual Creating an SU in the SU Database

Page 15

Basic Configuration via Browser Interface

CIR DOWN:

Committed Information Rate from AP to SU. Minimum downstream data rate (measured in

 

Kbps) at which the AP will attempt to deliver bandwidth to this SU. Maximum setting is

 

3000.

MIR UP:

Maximum Information Rate from SU to AP. Maximum upstream data rate (measured in

 

Kbps) at which the SU will attempt to deliver bandwidth to the AP. Maximum setting is

 

3000.

MIR UP:

Maximum Information Rate from AP to SU. Maximum data rate (measured in Kbps) at

 

which the AP will attempt to deliver bandwidth to this SU. Maximum setting is 3000.

DEVICE ID:

MAC address of the SU.

Creating an SU in the SU Database.

1.Connect to the AP (see Getting Started) and open the Subscriber Database page.

2.Enter SU ID (range 1 – 126).

3.Select either PRIORITY or REGULAR.

4.If SU will be part of an SU to SU group, enter the SU to SU group number.

5.CIR up: (SU to AP Committed Information Rate) – minimum upstream bandwidth for the SU in Kbps.

Trango Broadband Wireless — User Manual M900S Rev. C

Page 11

Image 15
Contents M900S MHz Wireless Broadband System Table of Contents Table of Figures Canada Warranty Information Firmware NotificationsPreface FCC InformationOverview IntroductionSmartPolling & Bandwidth Throttling Auto-retransmit Feature ARQM900S AP and SU Hardware Components Hardware OverviewGetting Started Connections and PowerCAT-5 Radio Management ConceptsBrowser Interface Switch SettingsWeb Browser System Information Browser Interface LoginTelnet ip address of radio Command Line InterfaceTroubleshooting Basic Configuration via Browser Interface Configuring the AP’s Subscriber Unit Database SudbThis section you will Creating an SU in the SU Database Active Channel/Polarization Configure Other Basic AP ParametersDefault Opmode IP Address, Subnet Mask, GatewayBasic Configuration via Browser Interface SU Basic Setup Configure Basic SU ParametersLED Summary LED SummaryLink Control RF Link Loopback TestSU Ranging Test Advanced SetupOther Key Parameters Site Survey Set baseid baseid Basic Configuration via CLIAccess Point Basic Settings AP Parameter Description Related CLI CommandSet apid apid 00-FF in HEX Set defaultopmode on or offSet defaultopmode on time sec Ipconfig new ip new subnet mask newSw 3 onoff default is off Power set minmaxdBmSw 0 onoff default is on On/off commandSudb add suid prreg device id suid SU ID Subscriber Unit Database Sudb SettingsSw 7 onoff default is on Remarks remarksSubscriber Unit Basic Settings Basic Configuration via CLI Set baseid baseid SU Parameter Description Related CLI CommandSet defaultopmode on or off Ipconfig new ip new subnet mask newSw 2 onoff Antenna h v eSw 0 onoff Sw 1 onoffMounting Hardware M900S Mounting Hardware AssemblyAlternative Mounting Standard Mounting Alternative Mounting Cabling and Grounding ConsiderationsInstallation Notes Command survey time antenna DeploymentSite Selection Example\ AP Search and SU Antenna AlignmentRssi Command for Antenna Alignment SU Alignment Using LEDsAP Search Collocation and Channel Planning Link Management CommandsSu su # Su ping su#Su testrflink su# Su linktest su#ARQ with Selected Repeat and Multirate Feature SU Management from AP Radio Management Access Via TCP/IPSu password suid all rw ro new password new password ManagementSnmp Loading Multiple SUs into the Sudb using Dload CommandObjects for Monitoring and Control SU Bandwidth MonitoringAP Bandwidth Monitoring Snmp Setup Command Radio Description Appendix a Command Set ReferenceCommand Radio Description Access Su ipconfig suid new IP new Command Radio Description Access Ethernet I/O Specifications Data Input/Output Appendix B SpecificationsRadio Transmit Specifications Receiver SpecificationsStandard External Power Supply Power SpecificationsMechanical and Environmental Specifications General Connectors/IndicatorsIntegrated Antenna M900S-SU and M900S-SU-EXT