Socket Mobile GFK0121E manual Using the 230VAC Power Adapter, Instructions

Page 12

2

Using the 230VAC Power Adapter

The optional 230VAC Power Adapter (IC660MCA512) can be used to connect the Hand- held Monitor Charger to variety of 230 VAC power outlets by means of a standard com- puter cable (not supplied).

The Adapter has a receptacle on the top for the Hand-held Monitor Charger and an IEC 320 receptacle on the side for the computer cable.

HHM Charger receptacle in

top of Adapter

IEC 320 receptacle in

side of Adapter

Instructions

1.Set the power selection switch on the Hand-held Monitor Charger to the 230V position.

120V

230V

230V position

2.Plug the Hand-held Monitor Charger into the top receptacle on the Power Adapter unit.

3.Plug the computer cable into the IEC receptacle on side of the Power Adapter unit.

4.Connect the computer cable to a suitable 230VAC power source.

During normal operation, it is best to connect and disconnect the cable at the outlet, not at the Adapter.

2-2

Hand-held Monitor User's Guide ± June 1994

GFK-0121E

Image 12

Contents GE Fanuc Automation GFL±002 Content of this Manual Related PublicationsPreface Contents Chapter Introduction Hand-held Monitor Description HHM KeypadKeyswitch AccessoriesHHM Display HHM Compatibility HHM Specifications Optional AccessoriesCharging the Battery Pack for AC Operation Selecting 120 VAC or 230 VACUsing the 230VAC Power Adapter InstructionsBattery Operation Low Battery PowerCharging the Battery Pack Replacing the Battery PackChanging the Prom Conductive mat Permanent Installation Configuring a Permanently-installed HHMHHM Installation Instructions CutoutInstalling the D-Shell HHM Connector SERInstalling a Separate Hand-held Monitor Connector Mounting the HHM ConnectorMaking the Bus Connections Chapter Getting Started Setting the HHM Baud Rate Powerup Error MessagesDisplaying the Home Menu Main HHM ScreensConfiguring the Hand-held Monitor Changing the HHM Device NumberChanging the HHM Display Language Selecting the Host CPUEnabling/Disabling Automatic Shutoff Enabling/Disabling the Ability to Clear Faults Enabling/Disabling the Ability to Force I/O CircuitsTesting Operation of the Hand-held Monitor Testing the Internal ElectronicsTesting the Keypad Testing the Display ScreenChapter Device Configuration Overview Online or Offline Configuration Starting ConfigurationOnline Configuration Offline ConfigurationDisplaying the Configuration Menus Completing the Program Block ID Screens To Set the I/O Map for a Remote I/O ScannerConfiguration Notes Configuring the Remote DropConfiguringGenius Blocks Copying a ConfigurationConfiguring Block Features Configuration InstructionsConfigure Additional Features Change the Bus AddressSelect a PLC Reference Address Configuring Individual Field Control Modules Disable the I/O ScanConfigure Data Addresses and Lengths Configuring Module Features Add Modules and Assign ReferencesAssign I/O References for the Module Chapter Monitoring the Bus and its Devices Displaying Information About Bus Devices Selecting Another DeviceSwitching a Dual Bus Monitoring the Bus StatusMonitoring a Genius Block Monitor Block Display for Discrete I/O and Input BlocksMaking the Block Active Block ReferencesMonitor Block Display for Discrete Relay OutputBlocks Monitor Block Display for Analog BlocksPreset Outputs Monitor Block Display for a High-speed Counter BlockMonitor Block Display for a PowerTRACBlock Calculated DataBasic Monitor/Control Display Format Diagnostics Clearing Circuit FaultsForcing an Input or Output Forcing an Analog, RTD, or Thermocouple Value Monitor/Control Reference Displays for a PowerTRAC Block PowerTRAC Data SequenceSelecting a Memory Type or Address PowerTRAC Status Inputs Screens PowerTRAC Calculated Data ScreensPowerTRAC Extra Calculated Data Lpio Screens PowerTRAC Control Outputs ScreensMonitoring/Controlling Remote Drop Data Displaying Other CircuitsDisplaying and Clearing Remote Drop Faults Clearing FaultsForcing a Circuit Changing the Display Mode Monitoring/Controlling Field Control DataDisplaying Another Reference Returning to the Previous MenuDisplaying Field Control Faults Clearing Field Control FaultsPulse Testing Outputs on Discrete Genius Blocks Clearing Pulse Test FaultsPulse Test Error Messages Executing a Pulse TestChapter Reading CPU Memory General InstructionsSeries 90 PLC Series Six PLC Enter or Change the PLC TypeEnter or Change the Memory Location Series Five PLC DataChanging the Data Format Changing the Selected AddressChapter Error Messages Powerup Error MessagesOperating Error Messages Configuration Error MessagesIndex Index-2 Index-3 Index-4