Socket Mobile GFK0121E manual GFL±002

Page 2

GFL±002

Warnings, Cautions, and Notes as Used in this Publication

Warning

Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use.

In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used.

Caution

Caution notices are used where equipment might be damaged if care is not taken.

Note

Notes merely call attention to information that is especially significant to understanding and operating the equipment.

This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems. GE Fanuc Automation assumes no obligation of notice to holders of this document with respect to changes subsequently made.

GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein. No warranties of merchantability or fitness for purpose shall apply.

The following are trademarks of GE FanucAutomationNorthAmerica,Inc.

Alarm Master

CIMSTAR

Helpmate

PROMACRO

Series Six

CIMPLICITY

GEnet

Field Control

Logicmaster

Series One

Series 90

CIMPLICITY 90±ADS

Genius

Modelmaster

Series Three

VuMaster

CIMPLICITY PowerTRAC

Genius PowerTRAC

ProLoop

Series Five

Workmaster

 

 

 

eCopyright 1994 GE Fanuc Automation North America, Inc.

All Rights Reserved

Image 2
Contents GE Fanuc Automation GFL±002 Content of this Manual Related PublicationsPreface Contents Chapter Introduction Hand-held Monitor Description HHM KeypadHHM Display KeyswitchAccessories HHM Compatibility HHM Specifications Optional AccessoriesCharging the Battery Pack for AC Operation Selecting 120 VAC or 230 VACUsing the 230VAC Power Adapter InstructionsCharging the Battery Pack Battery OperationLow Battery Power Replacing the Battery PackChanging the Prom Conductive mat Permanent Installation Configuring a Permanently-installed HHMHHM Installation Instructions CutoutInstalling the D-Shell HHM Connector SERInstalling a Separate Hand-held Monitor Connector Mounting the HHM ConnectorMaking the Bus Connections Chapter Getting Started Setting the HHM Baud Rate Powerup Error MessagesDisplaying the Home Menu Main HHM ScreensConfiguring the Hand-held Monitor Changing the HHM Device NumberEnabling/Disabling Automatic Shutoff Changing the HHM Display LanguageSelecting the Host CPU Enabling/Disabling the Ability to Clear Faults Enabling/Disabling the Ability to Force I/O CircuitsTesting the Keypad Testing Operation of the Hand-held MonitorTesting the Internal Electronics Testing the Display ScreenChapter Device Configuration Overview Online Configuration Online or Offline ConfigurationStarting Configuration Offline ConfigurationDisplaying the Configuration Menus Completing the Program Block ID Screens To Set the I/O Map for a Remote I/O ScannerConfiguration Notes Configuring the Remote DropConfiguring Block Features ConfiguringGenius BlocksCopying a Configuration Configuration InstructionsSelect a PLC Reference Address Configure Additional FeaturesChange the Bus Address Configure Data Addresses and Lengths Configuring Individual Field Control ModulesDisable the I/O Scan Assign I/O References for the Module Configuring Module FeaturesAdd Modules and Assign References Chapter Monitoring the Bus and its Devices Displaying Information About Bus Devices Selecting Another DeviceSwitching a Dual Bus Monitoring the Bus StatusMaking the Block Active Monitoring a Genius BlockMonitor Block Display for Discrete I/O and Input Blocks Block ReferencesMonitor Block Display for Discrete Relay OutputBlocks Monitor Block Display for Analog BlocksPreset Outputs Monitor Block Display for a High-speed Counter BlockMonitor Block Display for a PowerTRACBlock Calculated DataBasic Monitor/Control Display Format Forcing an Input or Output DiagnosticsClearing Circuit Faults Forcing an Analog, RTD, or Thermocouple Value Selecting a Memory Type or Address Monitor/Control Reference Displays for a PowerTRAC BlockPowerTRAC Data Sequence PowerTRAC Extra Calculated Data Lpio Screens PowerTRAC Status Inputs ScreensPowerTRAC Calculated Data Screens PowerTRAC Control Outputs ScreensMonitoring/Controlling Remote Drop Data Displaying Other CircuitsForcing a Circuit Displaying and Clearing Remote Drop FaultsClearing Faults Displaying Another Reference Changing the Display ModeMonitoring/Controlling Field Control Data Returning to the Previous MenuDisplaying Field Control Faults Clearing Field Control FaultsPulse Test Error Messages Pulse Testing Outputs on Discrete Genius BlocksClearing Pulse Test Faults Executing a Pulse TestChapter Reading CPU Memory General InstructionsSeries 90 PLC Enter or Change the Memory Location Series Six PLCEnter or Change the PLC Type Series Five PLC DataChanging the Data Format Changing the Selected AddressChapter Error Messages Powerup Error MessagesOperating Error Messages Configuration Error MessagesIndex Index-2 Index-3 Index-4