Socket Mobile GFK0121E manual Battery Operation, Low Battery Power, Charging the Battery Pack

Page 13

2

Battery Operation

The HHM's battery pack provides up to 6 hours of operation. To maximize battery life, allow the battery to discharge fully between charges. The battery should be allowed to fully discharge once a month.

Low Battery Power

Low battery power may cause this message:

* * L O W B A T T E R Y * * * * H H M H A L T E D * * P l e a s e R e c h a r g e

Or the display may blank, or two black lines may appear briefly. Low battery power suspends the current operation.

Charging the Battery Pack

When you receive a new Hand-held Monitor, its battery pack is not charged. Before using a new battery pack to power the HHM for the first time, charge it by plugging the adapter into a power source for 24 hours. After this initial charging, subsequent rechanges will require only 16 hours.

Maintaining spare battery packs will allow the HHM to operate using one battery pack while another is being charged.

If the battery pack won't take a charge, it usually indicates a faulty battery pack, not a faulty Hand-held Monitor. Try another battery pack. Replacement (uncharged) battery packs are available.

If a battery pack is left uncharged for a long time, it may be necessary to remove the battery pack from the HHM and charge it while removed for up to 15 minutes.

Replacing the Battery Pack

To replace the battery pack, use a Phillips screwdriver (size 0 or 1) to release the retaining screw at the bottom of the HHM. Slide the battery pack out, insert another, and tighten the screw.

Automatic Shutoff

To conserve power, the Hand-held Monitor automatically shuts off 10 minutes after the last key is pressed. For applications where continual operation is preferred, the automatic shutoff feature can be disabled. See page 3-5 for more information.

GFK-0121E

Chapter 2 Hardware Setup

2-3

Image 13
Contents GE Fanuc Automation GFL±002 Related Publications Content of this ManualPreface Contents Chapter Introduction HHM Keypad Hand-held Monitor DescriptionAccessories KeyswitchHHM Display HHM Compatibility Optional Accessories HHM SpecificationsSelecting 120 VAC or 230 VAC Charging the Battery Pack for AC OperationInstructions Using the 230VAC Power AdapterLow Battery Power Battery OperationCharging the Battery Pack Replacing the Battery PackChanging the Prom Conductive mat Configuring a Permanently-installed HHM Permanent InstallationCutout HHM Installation InstructionsSER Installing the D-Shell HHM ConnectorMounting the HHM Connector Installing a Separate Hand-held Monitor ConnectorMaking the Bus Connections Chapter Getting Started Powerup Error Messages Setting the HHM Baud RateMain HHM Screens Displaying the Home MenuChanging the HHM Device Number Configuring the Hand-held MonitorSelecting the Host CPU Changing the HHM Display LanguageEnabling/Disabling Automatic Shutoff Enabling/Disabling the Ability to Force I/O Circuits Enabling/Disabling the Ability to Clear FaultsTesting the Internal Electronics Testing Operation of the Hand-held MonitorTesting the Keypad Testing the Display ScreenChapter Device Configuration Overview Starting Configuration Online or Offline ConfigurationOnline Configuration Offline ConfigurationDisplaying the Configuration Menus To Set the I/O Map for a Remote I/O Scanner Completing the Program Block ID ScreensConfiguring the Remote Drop Configuration NotesCopying a Configuration ConfiguringGenius BlocksConfiguring Block Features Configuration InstructionsChange the Bus Address Configure Additional FeaturesSelect a PLC Reference Address Disable the I/O Scan Configuring Individual Field Control ModulesConfigure Data Addresses and Lengths Add Modules and Assign References Configuring Module FeaturesAssign I/O References for the Module Chapter Monitoring the Bus and its Devices Selecting Another Device Displaying Information About Bus DevicesMonitoring the Bus Status Switching a Dual BusMonitor Block Display for Discrete I/O and Input Blocks Monitoring a Genius BlockMaking the Block Active Block ReferencesMonitor Block Display for Analog Blocks Monitor Block Display for Discrete Relay OutputBlocksMonitor Block Display for a High-speed Counter Block Preset OutputsCalculated Data Monitor Block Display for a PowerTRACBlockBasic Monitor/Control Display Format Clearing Circuit Faults DiagnosticsForcing an Input or Output Forcing an Analog, RTD, or Thermocouple Value PowerTRAC Data Sequence Monitor/Control Reference Displays for a PowerTRAC BlockSelecting a Memory Type or Address PowerTRAC Calculated Data Screens PowerTRAC Status Inputs ScreensPowerTRAC Extra Calculated Data Lpio Screens PowerTRAC Control Outputs ScreensDisplaying Other Circuits Monitoring/Controlling Remote Drop DataClearing Faults Displaying and Clearing Remote Drop FaultsForcing a Circuit Monitoring/Controlling Field Control Data Changing the Display ModeDisplaying Another Reference Returning to the Previous MenuClearing Field Control Faults Displaying Field Control FaultsClearing Pulse Test Faults Pulse Testing Outputs on Discrete Genius BlocksPulse Test Error Messages Executing a Pulse TestGeneral Instructions Chapter Reading CPU MemorySeries 90 PLC Enter or Change the PLC Type Series Six PLCEnter or Change the Memory Location Data Series Five PLCChanging the Selected Address Changing the Data FormatPowerup Error Messages Chapter Error MessagesConfiguration Error Messages Operating Error MessagesIndex Index-2 Index-3 Index-4