Socket Mobile GFK0121E manual HHM Installation Instructions, Cutout

Page 17

2

HHM Installation Instructions

1.Select a suitable location for the HHM. Environmental specifications are listed on page 1-5. The location must have 115 VAC or 230 VAC power.

2.Cut an opening 3.75I(9.53cm) wide x 8I(20.32cm) high in the panel. Drill four mounting holes as shown below.

4.38in

(11.13cm)

3.75in

(9.53cm)

Cutout

1.00in (2.54cm)

6.00in

(15.24cm)

1.00in (2.54cm)

3. Attach the bracket to the HHM with the screws, washers, and lockwashers provided.

(4) holes for mounting on panel

(2) holes for mounting to back of Hand-held Monitor

4.Using appropriate hardware (not provided), mount the HHM and bracket in the cutout.

5.Connect the power cord to the HHM, and connect the signal cable to the connector.

GFK-0121E

Chapter 2 Hardware Setup

2-7

Image 17

Contents GE Fanuc Automation GFL±002 Related Publications Content of this ManualPreface Contents Chapter Introduction HHM Keypad Hand-held Monitor DescriptionHHM Display KeyswitchAccessories HHM Compatibility Optional Accessories HHM SpecificationsSelecting 120 VAC or 230 VAC Charging the Battery Pack for AC OperationInstructions Using the 230VAC Power AdapterLow Battery Power Battery OperationCharging the Battery Pack Replacing the Battery PackChanging the Prom Conductive mat Configuring a Permanently-installed HHM Permanent InstallationCutout HHM Installation InstructionsSER Installing the D-Shell HHM ConnectorMounting the HHM Connector Installing a Separate Hand-held Monitor ConnectorMaking the Bus Connections Chapter Getting Started Powerup Error Messages Setting the HHM Baud RateMain HHM Screens Displaying the Home MenuChanging the HHM Device Number Configuring the Hand-held MonitorEnabling/Disabling Automatic Shutoff Changing the HHM Display LanguageSelecting the Host CPU Enabling/Disabling the Ability to Force I/O Circuits Enabling/Disabling the Ability to Clear FaultsTesting the Internal Electronics Testing Operation of the Hand-held MonitorTesting the Keypad Testing the Display ScreenChapter Device Configuration Overview Starting Configuration Online or Offline ConfigurationOnline Configuration Offline ConfigurationDisplaying the Configuration Menus To Set the I/O Map for a Remote I/O Scanner Completing the Program Block ID ScreensConfiguring the Remote Drop Configuration NotesCopying a Configuration ConfiguringGenius BlocksConfiguring Block Features Configuration InstructionsSelect a PLC Reference Address Configure Additional FeaturesChange the Bus Address Configure Data Addresses and Lengths Configuring Individual Field Control ModulesDisable the I/O Scan Assign I/O References for the Module Configuring Module FeaturesAdd Modules and Assign References Chapter Monitoring the Bus and its Devices Selecting Another Device Displaying Information About Bus DevicesMonitoring the Bus Status Switching a Dual BusMonitor Block Display for Discrete I/O and Input Blocks Monitoring a Genius BlockMaking the Block Active Block ReferencesMonitor Block Display for Analog Blocks Monitor Block Display for Discrete Relay OutputBlocksMonitor Block Display for a High-speed Counter Block Preset OutputsCalculated Data Monitor Block Display for a PowerTRACBlockBasic Monitor/Control Display Format Forcing an Input or Output DiagnosticsClearing Circuit Faults Forcing an Analog, RTD, or Thermocouple Value Selecting a Memory Type or Address Monitor/Control Reference Displays for a PowerTRAC BlockPowerTRAC Data Sequence PowerTRAC Calculated Data Screens PowerTRAC Status Inputs ScreensPowerTRAC Extra Calculated Data Lpio Screens PowerTRAC Control Outputs ScreensDisplaying Other Circuits Monitoring/Controlling Remote Drop DataForcing a Circuit Displaying and Clearing Remote Drop FaultsClearing Faults Monitoring/Controlling Field Control Data Changing the Display ModeDisplaying Another Reference Returning to the Previous MenuClearing Field Control Faults Displaying Field Control FaultsClearing Pulse Test Faults Pulse Testing Outputs on Discrete Genius BlocksPulse Test Error Messages Executing a Pulse TestGeneral Instructions Chapter Reading CPU MemorySeries 90 PLC Enter or Change the Memory Location Series Six PLCEnter or Change the PLC Type Data Series Five PLCChanging the Selected Address Changing the Data FormatPowerup Error Messages Chapter Error MessagesConfiguration Error Messages Operating Error MessagesIndex Index-2 Index-3 Index-4