Socket Mobile GFK0121E manual Index-3

Page 63

Index

LCD display, 1-1

Loss of I/O Power diagnostic, 5-9Low power, 2-3

M

Memory, reading, 6-1Menus, main, 3-3Monitor Block screens, 5-4Monitor Only error, 7-2

Monitor/Control Reference screens for Field Processor, 5-15

for Genius blocks, 5-8

for Remote I/O Scanner, 5-13Monitoring, menus, 5-1Mounting bracket, 2-7

N

No Active Address error, 7-2No Faults diagnostic, 5-12No Load diagnostic, 5-9No Such Device error, 7-2Not Byte Boundary error, 7-2Not on Block error, 7-2

PowerTRAC block data sequence, 5-11display data, 5-7

Monitor/Control Reference screens, 5-11

Powerup, 3-2

Powerup Error messages, 7-1

Program Block ID screens, 4-4

PROM, changing, 2-4

Pulse Testing outputs, 5-17

R

Redundant bus, 5-4switching, 5-3

References

asterisks appear on screen, 5-2not on byte bundary, 7-2

of Genius block, displaying, 5-4

Relay blocks, monitor block screen, 5-5

Remote drop, configuration, 4-5

Remote I/O Scanner

compatibility with HHM versions, 1-4configuring I/O map, 4-4 , 4-5

RTD blocks

Monitor block screen, 5-5Monitor/Control Reference screens, 5-10

O

Open Wire diagnostic, 5-9 , 5-10Operating time, 1-5

Out of Range error, 7-2Overload diagnostic, 5-9Overrange diagnostic, 5-10Overtemperature diagnostic, 5-9 , 5-10

P

PCIM/QBIM, selecting as host, 3-5Power, display for PowerTRAC block, 5-11Power sources, 2-1

S

Serial bus address configuring for HHM, 3-4error caused by duplicating, 7-2of bus device, changing, 4-4

Series 90 PLC reading memory, 6-2references displayed, 5-2selecting as host type, 3-5

Series Five PLC reading memory, 6-4references displayed, 5-2selecting as host type, 3-5

Series Six PLC reading memory, 6-3references displayed, 5-2selecting as host type, 3-5

GFK-0121E

Index-3

 

Image 63
Contents GE Fanuc Automation GFL±002 Related Publications Content of this ManualPreface Contents Chapter Introduction HHM Keypad Hand-held Monitor DescriptionKeyswitch AccessoriesHHM Display HHM Compatibility Optional Accessories HHM SpecificationsSelecting 120 VAC or 230 VAC Charging the Battery Pack for AC OperationInstructions Using the 230VAC Power AdapterReplacing the Battery Pack Battery OperationLow Battery Power Charging the Battery PackChanging the Prom Conductive mat Configuring a Permanently-installed HHM Permanent InstallationCutout HHM Installation InstructionsSER Installing the D-Shell HHM ConnectorMounting the HHM Connector Installing a Separate Hand-held Monitor ConnectorMaking the Bus Connections Chapter Getting Started Powerup Error Messages Setting the HHM Baud RateMain HHM Screens Displaying the Home MenuChanging the HHM Device Number Configuring the Hand-held MonitorChanging the HHM Display Language Selecting the Host CPUEnabling/Disabling Automatic Shutoff Enabling/Disabling the Ability to Force I/O Circuits Enabling/Disabling the Ability to Clear FaultsTesting the Display Screen Testing Operation of the Hand-held MonitorTesting the Internal Electronics Testing the KeypadChapter Device Configuration Overview Offline Configuration Online or Offline ConfigurationStarting Configuration Online ConfigurationDisplaying the Configuration Menus To Set the I/O Map for a Remote I/O Scanner Completing the Program Block ID ScreensConfiguring the Remote Drop Configuration NotesConfiguration Instructions ConfiguringGenius BlocksCopying a Configuration Configuring Block FeaturesConfigure Additional Features Change the Bus AddressSelect a PLC Reference Address Configuring Individual Field Control Modules Disable the I/O ScanConfigure Data Addresses and Lengths Configuring Module Features Add Modules and Assign ReferencesAssign I/O References for the Module Chapter Monitoring the Bus and its Devices Selecting Another Device Displaying Information About Bus DevicesMonitoring the Bus Status Switching a Dual BusBlock References Monitoring a Genius BlockMonitor Block Display for Discrete I/O and Input Blocks Making the Block ActiveMonitor Block Display for Analog Blocks Monitor Block Display for Discrete Relay OutputBlocksMonitor Block Display for a High-speed Counter Block Preset OutputsCalculated Data Monitor Block Display for a PowerTRACBlockBasic Monitor/Control Display Format Diagnostics Clearing Circuit FaultsForcing an Input or Output Forcing an Analog, RTD, or Thermocouple Value Monitor/Control Reference Displays for a PowerTRAC Block PowerTRAC Data SequenceSelecting a Memory Type or Address PowerTRAC Control Outputs Screens PowerTRAC Status Inputs ScreensPowerTRAC Calculated Data Screens PowerTRAC Extra Calculated Data Lpio ScreensDisplaying Other Circuits Monitoring/Controlling Remote Drop DataDisplaying and Clearing Remote Drop Faults Clearing FaultsForcing a Circuit Returning to the Previous Menu Changing the Display ModeMonitoring/Controlling Field Control Data Displaying Another ReferenceClearing Field Control Faults Displaying Field Control FaultsExecuting a Pulse Test Pulse Testing Outputs on Discrete Genius BlocksClearing Pulse Test Faults Pulse Test Error MessagesGeneral Instructions Chapter Reading CPU MemorySeries 90 PLC Series Six PLC Enter or Change the PLC TypeEnter or Change the Memory Location Data Series Five PLCChanging the Selected Address Changing the Data FormatPowerup Error Messages Chapter Error MessagesConfiguration Error Messages Operating Error MessagesIndex Index-2 Index-3 Index-4