Socket Mobile GFK0121E manual Displaying the Home Menu, Main HHM Screens

Page 23

3

Displaying the Home Menu

This is the Hand-held Monitor's Home menu:

F 1 : H H M U T I L I T I E S

F 2	: A	N	A	L	Y	Z	E
F 3 : C O N F I G U R A T I O N
F 4 : D E V I C E							M E M O R Y

Display the Home menu by either:

A.Pressing F4 (Ok) from the first baud rate screen, or

B.Pressing the Home key or DMenu key from a lower-level screen.

Use the Home menu to get to any other HHM function, as shown below.

Notice that different screens appear, depending on the type of device that is currently communicating with the HHM.

The Main HHM Screens

F1: HHM UTILITIES

F2: ANALYZE

F3: CONFIGURATION

F4: DEVICE MEMORY

F1

F1: HHM CONFIG

F2: SELF±TEST

F3: HELP

F1

HHM CONFIG

BLOCK NO. 0

chng nxt

See page 3-4 for instructions.

F2

F1: KEYPAD TEST

F2: DISPLAY TEST

F3: TEST INTRNALS

F4:

See page 3-7 for instructions.

F3

(help screens)

F2

F1: MONITOR BLOCK

F2: MNTR/CTRL REF

F3: BLOCK/BUS STS

F4: PULSE TEST

F1

REFS							O
3	4	5	6	7	8	9	0

O O O O O O O

A 1 0 0 0 1 1 1

See page 5-4 for instructions.

F2

MNTR/CNTL O

STATE: 0

NO FAULTS

>on off reles

See page 5-9 for instructions.

F3

REFSO DC16K 15 v2.0ACT

FORCED, NO FAULTS nxt prv actv bus

See page 5-2 for instructions.

F4

PULSE TEST

REFS0 NO FAULTS exec

See page 5-17 for instructions.

F3

F1: PROG BLOCK ID

F2: CONFIG BLOCK

F3: COPY CONFIG

F1

PROG BLOCK ID

I/O
BLOCK NO.
ref blk	nxt

See page 4-4 for instructions.

F2

(individualfeature configuration screens)

See GeniusI/O Blocks Manual or individualblock manual for instructions.

F3

COPY CONFIG

FROM : TO :

chng entr

See page 4-6 for instructions.

For Most Genius Devices

F2

F1: MONITOR

F2: CONFIGURATION

F1

F1 Monitor I/O

F2:Faults

F3 Previous Menu

See page 5-15 for instructions.

F2

F1: GENIUS CONFIG

F2: Module Config

F3: Previous Menu

See page 4-7 for instructions.

For Field

Control

F4

DEVICE MEMORY # (reference)

tgl chng entr SBA

See chapter 6 for instructions.

GFK-0121E

Chapter 3 Getting Started

3-3

Image 23

Contents GE Fanuc Automation GFL±002 Related Publications Content of this ManualPreface Contents Chapter Introduction HHM Keypad Hand-held Monitor DescriptionHHM Display KeyswitchAccessories HHM Compatibility Optional Accessories HHM SpecificationsSelecting 120 VAC or 230 VAC Charging the Battery Pack for AC OperationInstructions Using the 230VAC Power AdapterReplacing the Battery Pack Battery OperationLow Battery Power Charging the Battery PackChanging the Prom Conductive mat Configuring a Permanently-installed HHM Permanent InstallationCutout HHM Installation InstructionsSER Installing the D-Shell HHM ConnectorMounting the HHM Connector Installing a Separate Hand-held Monitor ConnectorMaking the Bus Connections Chapter Getting Started Powerup Error Messages Setting the HHM Baud RateMain HHM Screens Displaying the Home MenuChanging the HHM Device Number Configuring the Hand-held MonitorEnabling/Disabling Automatic Shutoff Changing the HHM Display LanguageSelecting the Host CPU Enabling/Disabling the Ability to Force I/O Circuits Enabling/Disabling the Ability to Clear FaultsTesting the Display Screen Testing Operation of the Hand-held MonitorTesting the Internal Electronics Testing the KeypadChapter Device Configuration Overview Offline Configuration Online or Offline ConfigurationStarting Configuration Online ConfigurationDisplaying the Configuration Menus To Set the I/O Map for a Remote I/O Scanner Completing the Program Block ID ScreensConfiguring the Remote Drop Configuration NotesConfiguration Instructions ConfiguringGenius BlocksCopying a Configuration Configuring Block FeaturesSelect a PLC Reference Address Configure Additional FeaturesChange the Bus Address Configure Data Addresses and Lengths Configuring Individual Field Control ModulesDisable the I/O Scan Assign I/O References for the Module Configuring Module FeaturesAdd Modules and Assign References Chapter Monitoring the Bus and its Devices Selecting Another Device Displaying Information About Bus DevicesMonitoring the Bus Status Switching a Dual BusBlock References Monitoring a Genius BlockMonitor Block Display for Discrete I/O and Input Blocks Making the Block ActiveMonitor Block Display for Analog Blocks Monitor Block Display for Discrete Relay OutputBlocksMonitor Block Display for a High-speed Counter Block Preset OutputsCalculated Data Monitor Block Display for a PowerTRACBlockBasic Monitor/Control Display Format Forcing an Input or Output DiagnosticsClearing Circuit Faults Forcing an Analog, RTD, or Thermocouple Value Selecting a Memory Type or Address Monitor/Control Reference Displays for a PowerTRAC BlockPowerTRAC Data Sequence PowerTRAC Control Outputs Screens PowerTRAC Status Inputs ScreensPowerTRAC Calculated Data Screens PowerTRAC Extra Calculated Data Lpio ScreensDisplaying Other Circuits Monitoring/Controlling Remote Drop DataForcing a Circuit Displaying and Clearing Remote Drop FaultsClearing Faults Returning to the Previous Menu Changing the Display ModeMonitoring/Controlling Field Control Data Displaying Another ReferenceClearing Field Control Faults Displaying Field Control FaultsExecuting a Pulse Test Pulse Testing Outputs on Discrete Genius BlocksClearing Pulse Test Faults Pulse Test Error MessagesGeneral Instructions Chapter Reading CPU MemorySeries 90 PLC Enter or Change the Memory Location Series Six PLCEnter or Change the PLC Type Data Series Five PLCChanging the Selected Address Changing the Data FormatPowerup Error Messages Chapter Error MessagesConfiguration Error Messages Operating Error MessagesIndex Index-2 Index-3 Index-4