Uniden SC200 manual Bands. Then press /BAND again to start band search

Page 15

5.Press and hold /BAND to start Limit search. The VFO knob allows you to toggle through the

bands. Then press /BAND again to start band search.

6.Press to stop Band serch, Limit search and WX scan. Also, press it to move to next higher channel or

frequency. Press and hold to change the search direction to upper side.

7.In Limit search, input the frequency and press to program the lower/higher frequency. Press to stop Band search, Limit search, and WX scan.

Also, press it to move to next lower channel or

frequency. Press and hold to change the search direction to lower side.

8.Press /ALERT to change the display mode when you program frequency or Alpha characters. Press and

hold /ALERT to set the Alert Beep function in Manual mode.

9.Use /CLR to enter the decimal point when programming a frequency into a channel. If you

make an entry error, press /CLR before the

key to erase the entry, and start over. Also, use

/CLR to clear the error message display.

10.Press to store a displayed frequency and CTCSS/CDCSS Data and Alpha characters into any displayed channel.

11.Press to “Lock Out” or prevent scanning of the displayed channel, including Priority Channels. (L/O

appears on the display.) To unlock a channel, press

again. can be used for Scan or SEARCH Modes.

12.There are 10 Preprogrammed NOAA and Canada

weather channels. Press /ATT to find the active NOAA and Canada weather channel in your area. WX appears on the display in Weather Mode. If you

want to set or reset the Attenuator function, press and

hold /ATT.

13

Image 15
Contents SC200 Do not short circuit the battery PrecautionsContents CTCSS/CDCSS Tone Frequencies Hz What is Scanning? What is Searching?About Your New SportCat What is Ctcss and CDCSS? Range Step Band Subject Types of CommunicationUnpacking Where to Obtain More InformationFeature Highlights Page Top View Controls and IndicatorsFront View Indicates Weather Scan Mode Page Bands. Then press /BAND again to start band search Page Installing the Battery Pack SetupInstalling the Belt Clip Using the EarphoneMounting the Flexible Antenna Operation Overview Readjust the volume to a comfortable listening levelPage Programming By Manual Entry Programming ChannelsDeleting a Stored Frequency Programming with SearchAppear on the display. If you want to store the frequency Programming Channels with Alpha Characters Alert Beep Setting Bank Scanning ScanningPriority Scan DelayLooking for Locked Out Channels Locking Out ChannelsBand Weather Channel ScanningPress Enter the lower limit of your search range SearchingBand Search Limit SearchSearch Skip Frequency VFO SearchProgramming a Ctcss Tone/CDCSS Tone CTCSS/CDCSS OperationSearching for Ctcss Tones/CDCSS Tones Using Tone Search Change per 1sec Using Ctcss Tone or Cdcss Tone Search While Searching Ctcss and DCS begins flashing in display Changing a CTCSS/CDCSS Tone Press to change the Ctcss tone Erasing a CTCSS/CDCSS TonePage Remote Interface Connecting the ScannerSmartScan Mode Scanner to External ModemScanner to Scanner Page Page Whenever you press Transfer speed Flow control setting Xon/Xoff, RTS/CTS, Off Dial typeMenu for SmartScan Program LockTransfer Speed Flow ControlPress . The phone number appears Press to place the call Smartscanner Tips Dial TypePress . Clone Mode Clone ModeOn the scanner that is the Slave Unit, press Key until Replacing the Battery Pack Care and MaintenanceCleaning LocationRepairs Proper Care of Your Scanner BirdiesTechnical Specifications Size 2-1/2 W x 1-3/4 D x 11-3/4 H With antenna attached Ctcss CTCSS/CDCSS Tone Frequencies HzOptional Accessories Replacement Parts Problem Solution TroubleshootingProblem Solution One Year Limited Warranty Page Covered Under ONE or More of the Following U.S. Patents