Uniden BC785D manual Auto Store, Select Bank, Error, CH Data Full

Page 43

Auto Storing

The scanner automatically stores active frequencies if its Auto Store feature is turned ON. But the frequencies already stored can not be stored. To make use of this feature, set a search range first (see page 36), then enter into the Menu mode. If you start this feature without setting a search range, NO LIMIT DATA appears on the display.

1.Press MENU.

2.Select 1:SERVICE OPTION / :CHAIN SEARCH / 7:AUTO STORE by rotating the VFO and pressing E.

3.Select 1:ON by rotating the VFO and pressing E.

Remember! You can also use or instead of rotating the

AUTO STORE

VFO. Also instead of pressing E, you can press the VFO

SELECT BANK

control.

12--56----

 

4. Select the bank number you want to use with the keypad.

 

The selected bank number appears on the display.

 

 

Note: If the selected bank has no free channels to store, CH

AUTO STORE

DATA FULL will appear on the display and you will

ERROR

hear a beep.

CH DATA FULL

6. Press SRCH to start auto storing.

 

7.After the search has gone through the search range, press /HOLD to stop this feature. STORE END appears on the display. You may want to let it run through the search range several times again because during the first pass there may not have been any transmissions at that particular time on that frequency.

Squelch (SQ) Mode

The scanner can be set to the following SQ modes.

C 001

1245.8500 NFM Bank 12--56----

AUTO STORE

Carrier SQ mode (default setting)

The scanner will stop on any transmission or squelch opening, regardless of whether any subaudible tone has been programmed for the channel or search range.

Tone SQ mode

The scanner will stop on any active frequency for which either no subaudible tone has been programmed or for which the user-programmed subaudible tone is also active.

Tone Search mode

During any transmission, the scanner will begin searching all possible subaudible tones, one of which may also be in use. The scanner counts up through the CTCSS tones and instantly determines any possible DCS tone. See Page 91 for a listing of the tones that the BC785D decodes.

Note: When Tone Search is active in Scan mode, once the CTCSS or DCS display flashes a tone repeatedly (meaning that it has found the tone match), you can press E to program that frequency with the captured tone. When you change the mode to Tone SQ from Tone Search that frequency and tone will be programmed.

39

Image 43
Contents Page Page Contents Edacs Scat LTR IntroductionBC785D Front and Rear ViewIcon Description BC785D Shortcuts Entered. To begin Searching between the Range, press Srch Important Notice Terminology What is Scanning?What is Searching? What is Trunk Tracking?What is Apco Project 25 Digital Communications? Feature Highlights Information on the Internet Where to Obtain More InformationScanner.uniden.com Included with Your Scanner Package Optional Antenna SetupConnecting an Antenna Mounting an AntennaMounting the Scanner in Your Vehicle Typical Mounting MethodsApplying Power for Vehicle Installation Connecting an Earphone Desktop InstallationApplying Power Using Standard AC Power Connecting an External SpeakerRemember Connecting the Clone CableConnecting the Tape Recorder Listening SafelyBasic Operation Setting the SquelchTurn the Scanner On Understanding the Menu System Menu Description and Numeric Keypad Equivalents Set attenuation for all search ranges 2DELAY You can assign a variety of step sizes to the channel 9I-CALLMOTOROLA/EDACS Allows you to change the brightness of the display 6CLONE 1FREQUENCY Storing Frequencies into Channels in Menu ModeProgramming 001C1000 0000.0000 Error OUT of Channel010 512.0000 NFM OUT of BandAssigning a Text Tag to a Channel Transfer FrequenciesStoring Text Tags Assigning a Bank Tag to a BankProgramming Tips Beep AlertAssigning the Beep Alert to a Channel Scan Scan Hold FeatureTo directly access a specific channel ScanningDuring Scanning RF Attenuation FeatureSetting the Delay Mode for Frequency Storing Frequencies During Scanning001 141.5000 NFM Uniden Group a Lockout in Hold ModeChannel Lockout Restoring a Locked-out Channel Lockout in Scanning ModeRestoring All Locked-out Channels 001 512.0000 NFM Error PRI CH LockoutPriority on 010 1240.0000 NFMPriority Channel Plus Scan Searching Setting a Search RangeSrch 12.5k Data Skip Search Hold FeatureSrch 12.5k 1240.0000 NFM Range 25cm Amateur Grp Starting Chain SearchFrequency Skip Srch 12.5k 1240.0000 NFM Range C004Storing Search Frequencies CH Data Full ErrorAuto Store Select BankFor Search mode, select 1SERVICE Option / Chain Search Additional Menu Options for Searching 001 512.0000 NFM Ctcss 250.3 Bank003 512.0000 NFM Ctcss Uniden Group a 0032PUBLIC Safety 3NEWS Service SearchNWR-SAME Alert Service Search SkipFips Code Testing the Alert SirenProgramming Fips Code Digital and Trunked Systems 001 OOOO.0000 Programming and Receiving Digital and Trunked SystemsSelecting or Changing Trunking System Type Programming Trunking Frequencies 010Programming ID Scan Lists Manually E5-0 09-022¡ M5-0 4128 1216¡Enter ID M5-0 050-2¡Enter Alpha TAG M5-0 1216Receiving Trunked Systems Trunked Search ID Scan ModeID Scan Hold Feature M1-14128 867.8375 NFM ID Tag List Tag C1000 0000.0000 BankMOT ID8192 ID Monitor ModeID Search Hold and Direct Entry ID Hold Mode M1-14128Restoring Locked-out IDs LT ID0-02-042ID Review Review ID LockoutProgramming Scan Lists During Search Setting the Delay Mode for Trunking ModeSetting Priority in Trunking Mode ID tag Bank04 MOT TYP2Call Motorola/EDACS MOT ID LIST01 No.01 M1-1 851.0375 NFMDeleting a Stored ID Moving between Scan List MemoriesTalkgroups Multi-TrackMulti-Track Operational Details Edacs Tracking Edacs ReceptionAn Edacs Trunked system Special Edacs FeaturesEmergency Call Alert Edacs Scat LTR Tracking LTR ReceptionMotorola Tracking Motorola Reception001 867.8375 NFM NFM Select Fleet MAP Preset1TYPE2 Programming a Hybrid System NFM Block 0 Size Code50.0 Control Channel Only ModeToggling the Status Bit Disconnect Tone Detect Option End Code Apco Project 25 Reception Installing the Apco P-25 cardTurning ON/OFF the Apco P-25 Card Precautions for Installing the BCi25D Card867.8375 P25 Low Mid Upp 0533 1985 Apco P-25 Sound Quality Fine TuningThreshold Adjustment Range Sound QULTY0050Page To program your scanner PC Control ModeRemote Interface To connect Scanner to PCScanner.uniden.com PC Control Parameter Clone ModeStart Remote Mode and Change Transfer Speed Speed 39600 bps 419200 bps 5OFFTo connect the Scanner to Scanner Clone Clone Master Unit Slave UnitKey Beep Option Additional FeaturesDimmer Enter LockChannel Step Selection Reverse ModeReceiving Mode Selection Frequency and Channel Tuning with the VFO ControlCare and Maintenance Troubleshooting Problem Suggestion Specifications Glossary of Terms Page Page Appendix Preset Fleet MapsPreset Map Block Type I Programming Information User Defined Fleet MapsSize Code Restrictions Fleet Map Size CodesNWR-SAME Event Code Reverse List DCS Tone Code Ctcss Frequency List HzBC785D Flow Charts Scan Option Conventional System Option Dimmer Uniden America Corporation One Year Limited Warranty